Home › Engine / Hybrid System › 3ZR-FAE (STARTING) › STARTER
RM32H0E _51 Engine / Hybrid System _060200 3ZR-FAE STARTING _0295165 STARTER G

3ZR-FAE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A394482

Remove the nut, and disconnect the field coil lead wire from terminal C.


ii.
A394483C01
1.667,1.344 1.5,1.01 false 2.938,1.427 2.771,0.865 true 2.938,2.542 2.604,1.542 true 1.323,0.823 1.635,1.021 0.313,0.198 10 false *c 2.594,0.698 2.906,0.896 0.313,0.198 10 false *a 2.896,2.604 3.208,2.802 0.313,0.198 10 false *b
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Moves outward


Connect a battery to the magnet starter switch assembly as shown in the illustration. Check that the pinion gear moves outward.

If the pinion gear does not move outward, replace the magnet starter switch assembly.



b.

Perform a hold-in test.

i.
A394484C01
1.51,1.302 1.448,1.01 false 2.823,2.385 2.604,1.479 true 2.969,1.354 2.854,0.833 true 2.667,0.667 2.979,0.823 0.313,0.156 10 false *a 2.771,2.448 3.083,2.604 0.313,0.156 10 false *b 1.302,0.833 1.615,0.99 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect


While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the pinion gear does not return inward.

If the pinion gear returns inward, replace the magnet starter switch assembly.



c.

Perform a return test.

i.
A394485C01
1.719,1.406 1.594,1.156 false 3.042,1.469 2.844,0.969 true 2.896,2.531 2.656,1.573 true 2.698,0.802 3.01,0.958 0.313,0.156 10 false *a 2.844,2.594 3.156,2.75 0.313,0.156 10 false *b 1.448,1 1.76,1.156 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect
V100136

Returns inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.

Perform a no-load performance test.

i.
A394486

Connect the field coil lead wire to terminal C with the nut. Make sure that the field coil lead wire is not grounded.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


ii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A394487C01
1.354,1.938 0.958,1.531 false 2.396,1.844 1.927,1.125 true 2.625,2.01 2.292,3.094 true 1.75,0.969 2.063,1.125 0.313,0.156 10 false *a 2.167,3.125 2.479,3.281 0.313,0.156 10 false *b 0.792,1.396 1.104,1.552 0.313,0.156 10 false *c
*a Terminal 30
*b Terminal 50
*c Starter Body
V100135

Rotates


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A104908

Push in the plunger and check that it returns quickly to its original position.

If the plunger does not operate as specified, replace the magnet starter switch assembly.



b.
A394488C01
1.167,1.615 1.521,1.385 false 2.01,1.354 2.427,1.354 true 2.521,1.26 2.833,1.417 0.313,0.156 10 false *a 1.01,1.646 1.323,1.802 0.313,0.156 10 false *b
*a Terminal 50
*b Terminal C


Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A394489C01
1.667,1.75 2,1.375 true 1.125,0.427 1.417,0.167 false 1.542,1.781 1.854,1.938 0.313,0.156 10 false *a 1.49,0.073 1.802,0.229 0.313,0.156 10 false *b
*a Terminal 50
*b Magnet Starter Switch Assembly Body


Check the holding coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 -Magnet switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.



Hide 28160 3.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator appearance.

If the surface is dirty or burnt, restore it with sandpaper (400-grit) or on a lathe.


b.
A394490C01
1.813,1.177 0.979,1.323 0.979,1.323 1.979,0.865 true 0.781,1.25 1.094,1.406 0.313,0.156 10 false *a
*a Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.
A394491C01
0.74,0.677 1.281,0.854 true 2.042,1.156 2.615,0.583 true 2.708,0.458 3.021,0.615 0.313,0.156 10 false *a 0.521,0.573 0.833,0.729 0.313,0.156 10 false *b
*a Segment
*b Starter Armature Coil Core


Check the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A394492C01
1.031,1.146 1.031,1.854 1.031,1.854 2.281,1.531 true 0.927,1.896 1.24,2.052 0.313,0.156 10 false *a
*a Armature Shaft


Check the commutator for runout.

i.

Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the runout.

Standard Runout:

0.02 mm (0.000787 in.)


Maximum Runout:

0.04 mm (0.00157 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A394493C02
0.469,0.302 0.781,0.458 0.313,0.156 10 false *a
*a Diameter


Using a vernier caliper, measure the commutator diameter.

Standard Diameter:

25.9 mm (1.0197 in.)


Minimum Diameter:

24.9 mm (0.9803 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A105577C02
2.99,0.76 3.302,0.917 0.313,0.156 10 false *a
*a Undercut depth


Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard Undercut Depth:

0.9 mm (0.0354 in.)


Minimum Undercut Depth:

0.4 mm (0.0157 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A394494C01
2.646,0.698 2.958,0.896 0.313,0.198 10 false *a
*a Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard Length:

10.2 mm (0.402 in.)


Minimum Length:

7.0 mm (0.276 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



b.
A104910E04
1.26,1.177 0.76,1.177 false 1.438,1.677 0.833,1.677 false 2.573,1.313 2.896,1.313 false 2.26,0.854 2.802,0.854 false 0.615,1.104 0.729,1.302 0.115,0.198 10 A 0.708,1.604 0.917,1.813 0.208,0.208 10 B 2.948,1.25 3.146,1.458 0.198,0.208 10 C 2.833,0.792 2.948,0.99 0.115,0.198 10 D

Check the brush holder resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Specified Condition
A - B
A - C
B - D
C - D
10 kΩ or higher
A - D
B - C
Below 1 Ω


If the result is not as specified, replace the starter brush holder assembly.



Hide 5.INSPECT PLANET CARRIER SHAFT SUB-ASSEMBLY

a.
A321079C01
1.542,0.729 1.74,0.979 0.198,0.25 10 false *a 2.479,0.74 2.792,0.896 0.313,0.156 10 false *b
*a Free
*b Lock


Check the clutch gear.

i.

While holding the planet carrier shaft sub-assembly, rotate the clutch gear counterclockwise, and check that it turns freely. Try to rotate the clutch gear clockwise and check that it locks.

If the clutch gear does not operate as specified, replace the planet carrier shaft sub-assembly.



Hide 28120 6.INSPECT STARTER YOKE ASSEMBLY

a.
A329677C01
1.25,0.125 1.542,0.125 1.542,0.125 1.74,0.469 false 1.917,1.094 2.365,1.938 2.365,1.938 2.781,1.938 false 1.083,0.042 1.396,0.198 0.313,0.156 10 false *1 2.844,1.823 3.156,1.979 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*a Starter Water Drain Hose


Check the starter water drain hose for damage or clogs.

If there is damage or clogs, replace the starter yoke assembly.