Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for DENSO Made)
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0299517 AIR CONDITIONING UNIT(for DENSO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for DENSO Made)  REASSEMBLY  


PROCEDURE

Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

a.
E339399

Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case.


b.

Engage the clamp.


c.

Engage the claws to install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case.

E338020


d.

Install the 2 screws.


Hide 88515 3.INSTALL COOLER EXPANSION VALVE

a.

Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



b.

Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



c.
E338019

Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


d.
E338018

Install the grommet.


Hide 87107A 4.INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY

a.
E338017C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater radiator unit sub-assembly as shown in the illustration.


Hide 87124B 5.INSTALL HEATER CLAMP

a.
E338015

Engage the claws to install the heater clamp.


Hide 88897M 6.INSTALL HEATER PIPE GROMMET

a.
E337824

Install the heater pipe grommet.


Hide 87050C 7.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

a.

Align each gear on the air conditioner radiator assembly as shown in the illustration, and then check that the gears of the No. 1 air conditioning radiator damper servo sub-assembly arealigned as shown in the illustration.

E339385C01
5.896,1.052 4.313,0.854 4.313,0.854 5.083,1.26 true 2.479,1.906 3.438,0.875 3.438,0.875 1.958,1.635 true 3.479,0.74 3.792,0.896 0.313,0.156 10 false *a 4.115,0.729 4.427,0.885 0.313,0.156 10 false *a
*a Reference Point - -



b.

Using the reference points, install the No. 1 air conditioning radiator damper servo sub-assembly with the 3 screws.

E339386C01
5.167,0.854 5.167,1.24 5.167,1.24 5.292,0.917 true 5.083,1.271 5.396,1.427 0.313,0.156 10 false *a
*a Reference Point - -



Hide 88539J 8.INSTALL DRAIN COOLER HOSE

a.
E337816C01
1.302,2.458 1.656,2.865 true 2.115,3.01 1.688,2.948 true 1.042,2.302 1.26,2.5 0.219,0.198 10 true *a 2.146,2.875 2.365,3.073 0.219,0.198 10 true *b
*a Hose Notch
*b Rib


Align the hose notch with the rib as shown in the illustration and install the drain cooler hose.


Hide 88482A 9.INSTALL COVER

a.
I113812

Engage the claws to install the cover.


Hide 82210K 10.INSTALL AIR CONDITIONING HARNESS ASSEMBLY

a.

Engage the clamps.

I112486


b.

Connect 4 connectors to install the air conditioning harness assembly.


Hide 88650N 11.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

a.
E337295C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide to temporarily install the air conditioning amplifier assembly as shown in the illustration.


b.

Install the air conditioning amplifier assembly with the screw.


c.

Connect the connector.


Hide 87114B 12.INSTALL HEATER COVER

a.
E337819C01
0,0 0,0 false
V113147

Install in this Direction


Install the heater cover with the screw as shown in the illustration.


Hide 88505 14.INSTALL AIR CONDITIONING DUCT SUB-ASSEMBLY

a.
E337808

Engage the claws to install the air conditioning duct sub-assembly.


Hide 87211 15.INSTALL NO. 1 AIR DUCT

a.
I112805C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 1 air duct as shown in the illustration.


b.

Install the screw.