Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP (for 3ZR-FAE)
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0299737 VACUUM PUMP(for 3ZR-FAE) G

BRAKE SYSTEM (OTHER)  VACUUM PUMP(for 3ZR-FAE)  INSPECTION  


PROCEDURE

Hide 29331A 1.INSPECT VACUUM PUMP VANE

a.
C169339C12
1.802,1.281 1.802,1.469 false 2.75,1.042 2.75,1.24 false 0.656,1.51 0.656,1.708 false 1.74,1.5 2.24,1.729 0.5,0.229 10 false *2 2.688,1.271 3.156,1.583 0.469,0.313 10 false *1 0.594,1.719 1.25,1.969 0.656,0.25 10 false *1
*1 Vacuum Pump Vane Cap
*2 Vacuum Pump Vane


Check that the vacuum pump vane or vacuum pump vane caps are not damaged or excessively worn out.

HINT:

If the vacuum pump vane or vacuum pump vane caps are damaged or excessively worn out, replace the damaged parts with new ones.



b.
C169340C03
2.354,2.365 2.625,2.625 0.271,0.26 10 false (A) 1.271,2.365 1.531,2.573 0.26,0.208 10 false (A) 0.802,3 1.052,3.208 0.25,0.208 10 false *a 2.531,2.99 2.729,3.208 0.198,0.219 10 false *a
*a 10 mm (0.394 in.)


Using a micrometer, measure length (A) of the vacuum pump vane with the vacuum pump vane caps removed.

Minimum Length (A):

23.8 mm (0.937 in.)


NOTICE:

Measure length (A) 10 mm (0.394 in.) in from each end of the vacuum pump vane.


HINT:

If the length is not as specified, replace the vacuum pump vane and vacuum pump vane caps with new ones.



c.
C169342C06
0.948,1.969 0.948,1.719 0.948,1.719 1.406,1.719 false 2.448,2.625 2.448,2.875 false 0.552,2.625 0.552,2.875 false 2.729,1.969 2.958,2.188 0.229,0.219 10 false *a 2.74,2.469 3,2.656 0.26,0.188 10 false *a 1.479,1.656 1.646,1.823 0.167,0.167 10 false *1 2.365,2.938 2.531,3.104 0.167,0.167 10 false *2 0.458,2.927 0.625,3.094 0.167,0.167 10 false *2 1.427,1.979 1.667,2.177 0.24,0.198 10 false (B) 1.427,2.26 1.667,2.458 0.24,0.198 10 false (B)
*1 Vacuum Pump Vane
*2 Vacuum Pump Vane Cap
*a 5 mm (0.197 in.)


Using a vernier caliper, measure length (B) of the vacuum pump vane with the vacuum pump vane caps installed.

Minimum Length (B):

76 mm (2.99 in.)


NOTICE:

Measure length (B) 5 mm (0.197 in.) in from each end of the vacuum pump vane cap.


HINT:

If the length is not as specified, replace the vacuum pump vane and vacuum pump vane caps with new ones.



Hide 2.INSPECT VACUUM PUMP HOUSING

a.
C169338

Check that the rotor part, coupling, vacuum pump housing and end cover are not damaged or excessively worn out.

HINT:

If the rotor part, coupling, vacuum pump housing or end cover are damaged or excessively worn out, replace the vacuum pump assembly.