Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2016.10–2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0299845 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1532  LVDS Signal Malfunction (from Extension Module)  


DESCRIPTION

The navigation ECU and the radio and display receiver assembly are connected via LVDS communication line.

This DTC is stored when an LVDS communication error occurs between the navigation ECU and the radio and display receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1532 LVDS Signal Malfunction (from Extension Module) When any of the following conditions is met:
·

Video signal (digital) is lost.

·

Navigation ECU is/was not connected while the ignition switch is/was ACC or ON.

·

Communication between the master unit and the navigation ECU is/was not possible when the engine is/was started.


·

Navigation ECU power source circuit

·

LVDS circuit between radio and display receiver assembly and navigation ECU

·

Navigation ECU

·

Radio and display receiver assembly

·

Harness and connector



HINT:
·

Even if no malfunction is present, this DTC may be stored depending on the auxiliary battery condition or engine start voltage.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E361265E01
0.969,3.115 2.271,3.479 1.302,0.365 10 false Radio and Display Receiver Assembly 5.281,3.135 6.813,3.354 1.531,0.219 10 false Navigation ECU 5.177,0.615 6.708,0.833 1.531,0.219 10 false +B 5.188,1.01 6.719,1.229 1.531,0.219 10 false ACC 5.177,1.406 6.708,1.625 1.531,0.219 10 false GND 1.781,0.615 3.313,0.833 1.531,0.219 10 false +B2 1.688,1.01 3.219,1.229 1.531,0.219 10 false ACC2 1.677,1.396 3.208,1.615 1.531,0.219 10 false GND2 1.74,1.823 2.354,2.021 0.615,0.198 10 false LV1- 1.708,2.271 2.323,2.469 0.615,0.198 10 false LV1+ 1.688,2.719 2.302,2.917 0.615,0.198 10 false LVG1 5.167,2.729 5.781,2.927 0.615,0.198 10 false LVG1 5.177,2.292 5.792,2.49 0.615,0.198 10 false LV1+ 5.177,1.844 5.792,2.042 0.615,0.198 10 false LV1- 2.208,2.729 2.823,2.927 0.615,0.198 10 false k1 2.219,2.302 2.833,2.5 0.615,0.198 10 false k1 2.208,1.833 2.823,2.031 0.615,0.198 10 false k1 4.844,2.729 5.458,2.927 0.615,0.198 10 false k2 4.844,2.281 5.458,2.479 0.615,0.198 10 false k2 4.844,1.833 5.458,2.031 0.615,0.198 10 false k2 2.177,1.417 2.792,1.615 0.615,0.198 10 false F80 2.167,1.021 2.781,1.219 0.615,0.198 10 false F80 2.177,0.625 2.792,0.823 0.615,0.198 10 false F80 4.792,0.625 5.406,0.823 0.615,0.198 10 false F83 4.792,1.021 5.406,1.219 0.615,0.198 10 false F83 4.802,1.417 5.417,1.615 0.615,0.198 10 false F83 4.854,0.417 5.229,0.604 0.375,0.188 10 false 1 4.865,0.823 5.24,1.01 0.375,0.188 10 false 3 4.865,1.219 5.24,1.406 0.375,0.188 10 false 2 2.25,0.823 2.625,1.01 0.375,0.188 10 false 3 2.25,0.417 2.625,0.604 0.375,0.188 10 false 4 2.25,1.229 2.625,1.417 0.375,0.188 10 false 8 2.24,1.646 2.615,1.833 0.375,0.188 10 false 1 2.25,2.094 2.625,2.281 0.375,0.188 10 false 2 2.25,2.542 2.625,2.729 0.375,0.188 10 false 3 4.865,2.542 5.24,2.729 0.375,0.188 10 false 3 4.865,2.094 5.24,2.281 0.375,0.188 10 false 2 4.865,1.646 5.24,1.833 0.375,0.188 10 false 1 3.094,3.365 5.646,3.594 2.552,0.229 10 false : LVDS Communication Line 3.365,2.5 4.896,2.698 1.531,0.198 10 false (Shielded)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU POWER SOURCE)
a.

Disconnect the F83 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F83-2 (GND) - Body ground Always Below 1 Ω



c.
E317663C03
1.458,0.25 1.958,0.5 0.5,0.25 0.333,1.167 0.74,1.063 true 0.75,1.75 0.917,1.063 true 1.479,1.75 1.313,1.083 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.594,0.292 2.052,0.49 0.458,0.198 10 false F83 0.094,1.094 0.344,1.292 0.25,0.198 10 false +B 0.594,1.792 1.094,2.042 0.5,0.25 10 false GND 1.365,1.792 1.865,2.042 0.5,0.25 10 false ACC
*a Front view of wire harness connector
(to Navigation ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F83-1 (+B) - F83-2 (GND) Always 11 to 14 V
F83-3 (ACC) - F83-2 (GND) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.REPLACE HARNESS AND CONNECTOR (LVDS COMMUNICATION LINE)

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
2.REPLACE HARNESS AND CONNECTOR (LVDS COMMUNICATION LINE)
a.

Replace the harness and connector (LVDS communication line) with a new or known good one.


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

3.REPLACE NAVIGATION ECU
3.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.

Disconnect the F80 radio and display receiver assembly connector.


b.

Disconnect the F83 navigation ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-4 (+B2) - F83-1 (+B) Always Below 1 Ω
F80-3 (ACC2) - F83-3 (ACC) Always Below 1 Ω
F80-8 (GND2) - F83-2 (GND) Always Below 1 Ω
F80-4 (+B2) - Body ground Always 10 kΩ or higher
F80-3 (ACC2) - Body ground Always 10 kΩ or higher
F80-8 (GND2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR