Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2016.10–2019.09
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0300012 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Footwell Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the door mirror foot lights.

WIRING DIAGRAM

E363127E02
2.333,1.573 2.49,1.771 0.156,0.198 10 false + 1.51,1.583 1.667,1.781 0.156,0.198 10 false E 2.323,3.302 2.479,3.5 0.156,0.198 10 false + 1.521,3.302 1.677,3.5 0.156,0.198 10 false E 0.885,2.344 1.677,2.563 0.792,0.219 10 false I8*1, I7*2 0.865,2.521 3.188,2.833 2.323,0.313 10 false Outer Rear View Mirror Assembly RH 2.708,1.573 3.167,1.771 0.458,0.198 10 false MLP 2.708,3.313 3.167,3.51 0.458,0.198 10 false MLP 3.094,1.563 3.823,1.75 0.729,0.188 10 false 3*1, 2*2 3.094,3.292 3.75,3.479 0.656,0.188 10 false 3*1, 2*2 0.292,1.542 1,1.792 0.708,0.25 10 false 9*1, 12*2 0.281,3.281 0.906,3.469 0.625,0.188 10 false 9*1, 12*2 0.969,1.573 1.125,1.771 0.156,0.198 10 false - 0.948,3.313 1.104,3.51 0.156,0.198 10 false - 5.458,3.083 5.917,3.281 0.458,0.198 10 false F16 5.438,3.25 6.646,4.167 1.208,0.917 10 false Main Body ECU (Multiplex Network Body ECU) 5.229,1.573 5.385,1.771 0.156,0.198 10 false 4 5.448,1.573 6.063,1.771 0.615,0.198 10 false MILE 5.969,0.51 6.281,0.708 0.313,0.198 10 false +B 0.885,4.083 1.823,4.313 0.938,0.229 10 false J7*1, J11*2 0.875,4.25 3.219,4.625 2.344,0.375 10 false Outer Rear View Mirror Assembly LH 1.156,1.948 4.979,2.146 3.823,0.198 10 false Door Mirror Foot Light RH 1.177,3.708 2.844,3.969 1.667,0.26 10 false Door Mirror Foot Light LH 2.479,1.573 2.635,1.771 0.156,0.198 10 false 1 1.344,1.573 1.5,1.771 0.156,0.198 10 false 2 1.365,3.313 1.521,3.51 0.156,0.198 10 false 2 2.479,3.302 2.635,3.5 0.156,0.198 10 false 1 0.156,4.521 1.427,4.781 1.271,0.26 10 false *1: for TMMT Made 1.938,4.521 3.208,4.781 1.271,0.26 10 false *2: for TMC Made

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Side Mirror Foot Light Door mirror foot lights ON/OFF -
Body Electrical > Main Body > Active Test
Tester Display
Side Mirror Foot Light
50004 123 32
OK:

Door mirror foot lights illuminate.



Result:
Result Proceed to
OK A
NG (for LH Side) B
NG (for RH Side) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH (POWER SOURCE)

C

5.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH (POWER SOURCE)
2.CHECK OUTER REAR VIEW MIRROR ASSEMBLY LH (POWER SOURCE)
a.

Disconnect the J7*1 or J11*2 outer rear view mirror assembly LH connector.

*1: for TMMT Made

*2: for TMC Made



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for TMMT Made
Tester Connection Condition Specified Condition
J7-3 (MLP) - Body ground Illumination conditions of door mirror foot light met* 11 to 14 V

for TMC Made
Tester Connection Condition Specified Condition
J11-2 (MLP) - Body ground Illumination conditions of door mirror foot light met* 11 to 14 V


*: Refer to System Description for the illumination conditions of the door mirror foot light.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION


Result:
Proceed to
OK
NG



OK

3.INSPECT DOOR MIRROR FOOT LIGHT LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DOOR MIRROR FOOT LIGHT LH
a.

Remove the door mirror foot light LH.

Click hereVehicle Exterior>LIGHTING (EXT)>DOOR MIRROR FOOT LIGHT>REMOVAL


b.
E363559C03
0.833,1.76 1.469,1.177 true 2.542,1.771 1.948,1.177 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,1.76 0.833,1.958 0.156,0.198 10 false + 2.615,1.75 2.771,1.948 0.156,0.198 10 false E
*a Component without harness connected
(Door Mirror Foot Light LH)


Check door mirror foot light LH illumination.

i.

Apply battery voltage between the terminals of the door mirror foot light LH and check the illumination condition of the door mirror foot light LH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (E)
Illuminates




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)

NG

REPLACE DOOR MIRROR FOOT LIGHT LH

4.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY LH - BODY GROUND)
a.

Disconnect the J7*1 or J11*2 outer rear view mirror assembly LH connector.

*1: for TMMT Made

*2: for TMC Made



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
J7-9 (-) - Body ground Always Below 1 Ω

for TMC Made
Tester Connection Condition Specified Condition
J11-12 (-) - Body ground Always Below 1 Ω


*: Refer to System Description for the illumination conditions of the door mirror foot light.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK OUTER REAR VIEW MIRROR ASSEMBLY RH (POWER SOURCE)
a.

Disconnect the I8*1 or I7*2 outer rear view mirror assembly RH connector.

*1: for TMMT Made

*2: for TMC Made



b.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
for TMMT Made
Tester Connection Condition Specified Condition
I8-3 (MLP) - Body ground Illumination conditions of door mirror foot light met* 11 to 14 V

for TMC Made
Tester Connection Condition Specified Condition
I7-2 (MLP) - Body ground Illumination conditions of door mirror foot light met* 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT DOOR MIRROR FOOT LIGHT RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT DOOR MIRROR FOOT LIGHT RH
a.

Remove the door mirror foot light RH.

Click hereVehicle Exterior>LIGHTING (EXT)>DOOR MIRROR FOOT LIGHT>REMOVAL


b.
E363559C03
0.833,1.76 1.469,1.177 true 2.542,1.771 1.948,1.177 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,1.76 0.833,1.958 0.156,0.198 10 false + 2.615,1.75 2.771,1.948 0.156,0.198 10 false E
*a Component without harness connected
(Door Mirror Foot Light RH)


Check door mirror foot light RH illumination.

i.

Apply battery voltage between the terminals of the door mirror foot light RH and check the illumination condition of the door mirror foot light RH.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (+)
Battery negative (-) → Terminal 2 (E)
Illuminates




Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)

NG

REPLACE DOOR MIRROR FOOT LIGHT RH

7.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY RH - BODY GROUND)
a.

Disconnect the I8*1 or I7*2 outer rear view mirror assembly RH connector.

*1: for TMMT Made

*2: for TMC Made



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
I8-9 (-) - Body ground Always Below 1 Ω

for TMC Made
Tester Connection Condition Specified Condition
I7-12 (-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR