Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0298709 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  TERMINALS OF ECU  


AIR CONDITIONING AMPLIFIER ASSEMBLY


E352243N03
1.906,0.083 2.406,0.333 0.5,0.25 4.813,0.083 5.313,0.333 0.5,0.25 2.042,0.104 2.5,0.302 0.458,0.198 10 false F72 4.958,0.115 5.417,0.313 0.458,0.198 10 false F7A

HINT:

Check from the rear of the connector while it is connected to the air conditioning amplifier assembly.


Terminal No. (symbol) Wiring Color Terminal Description Condition Specified Condition
F72-1 (B) - Body ground V - Body ground Power source (Back-up) Always 11 to 14 V
F72-3 (LIN1) - F72-29 (GND) L - W-B*3
BE - W-B*4
LIN communication signal (Air conditioning control assembly) Ignition switch ON Pulse generation
(See waveform 1)
F72-5 (IG+) - Body ground B - Body ground Power Source (IG) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
F72-9 (CANH) - F72-10 (CANL) P - SB CAN communication CAN communication is performed Pulse generation
F72-15 (SOL-) - F72-29 (GND)*7 L - W-B Compressor solenoid operation
·

Engine running

·

Blower switch: Lo

·

A/C switch: On


Pulse generation
(See waveform 2)
F72-19 (PTC1) - F72-29 (GND)*1 L - W-B Output for driving PTC1 heater relay
·

Ignition switch ON

·

ECO mode: off

·

Temperature setting: MAX HOT

·

Ambient temperature: 25°C (77°F) or lower

·

Engine coolant temperature: 75°C (167°F) or lower

·

Light control switch off

·

Blower switch: Lo


Below 1 V
·

Ignition switch ON

·

ECO mode: off

·

Temperature setting: MAX HOT

·

Ambient temperature: 25°C (77°F) or lower

·

Engine coolant temperature: 75°C (167°F) or lower

·

Light control switch off

·

Blower switch: Off


11 to 14 V
F72-20 (PTC3) - F72-29 (GND)*1 BR - W-B Output for driving PTC3 heater relay
·

Ignition switch ON

·

ECO mode: off

·

Temperature setting: MAX HOT

·

Ambient temperature: -7°C (19°F) or lower

·

Engine coolant temperature: 65°C (149°F) or lower

·

Light control switch off

·

Blower switch: Lo


Below 1 V
·

Ignition switch ON

·

ECO mode: off

·

Temperature setting: MAX HOT

·

Ambient temperature: -7°C (19°F) or lower

·

Engine coolant temperature: 65°C (149°F) or lower

·

Light control switch off

·

Blower switch: Off


11 to 14 V
F72-29 (GND) - Body ground W-B - Body ground Ground for main power supply Always Below 1 V
F72-32 (SG-2) - Body ground*7 G - Body ground Ground for air conditioner pressure sensor Always Below 1 V
F72-33 (PRE) - F72-32 (SG-2)*5,*7 V - G Input from refrigerant gas sensor
·

Ignition switch ON

·

Air conditioning system operating

·

Refrigerant pressure: Abnormal pressure (more than 3025 kPa (30.8 kgf/cm2, 439 psi))


4.61 V or higher
·

Ignition switch ON

·

Air conditioning system operating

·

Refrigerant pressure: Abnormal pressure (less than 176 kPa (1.8 kgf/cm2, 26 psi))


Below 0.74 V
·

Ignition switch ON

·

Air conditioning system operating

·

Refrigerant pressure: Normal pressure (less than 3025 kPa (30.8 kgf/cm2, 439 psi) and more than 176 kPa (1.8 kgf/cm2, 26 psi))


0.74 to 4.61 V
F72-33 (PRE) - F72-32 (SG-2)*6,*7 V - G Input from refrigerant gas sensor
·

Ignition switch ON

·

Air conditioning system operating

·

Refrigerant pressure: Abnormal pressure (more than 2812 kPa (28.7 kgf/cm2, 408 psi))


4.61 V or higher
·

Ignition switch ON

·

Air conditioning system operating

·

Refrigerant pressure: Abnormal pressure (less than 195 kPa (2.0 kgf/cm2, 28 psi))


Below 0.74 V
·

Ignition switch ON

·

Air conditioning system operating

·

Refrigerant pressure: Normal pressure (less than 2812 kPa (28.7 kgf/cm2, 408 psi) and more than 195 kPa (2.0 kgf/cm2, 28 psi))


0.74 to 4.61 V
F72-34 (S5-3) - F72-32 (SG-2)*7 GR - G Power supply for air conditioner pressure sensor Ignition switch ON 4.75 to 5.25 V
Ignition switch off Below 1 V
F72-39 (PTC2) - F72-29 (GND)*1 V - W-B Output for driving PTC2 heater relay
·

Ignition switch ON

·

ECO mode: off

·

Temperature setting: MAX HOT

·

Ambient temperature: 16°C (61°F) or lower

·

Engine coolant temperature: 70°C (158°F) or lower

·

Light control switch off

·

Blower switch: Lo


Below 1 V
·

Ignition switch ON

·

ECO mode: off

·

Temperature setting: MAX HOT

·

Ambient temperature: 16°C (61°F) or lower

·

Engine coolant temperature: 70°C (158°F) or lower

·

Light control switch off

·

Blower switch: Off


11 to 14 V
F7A-1 (SHUNT1) - Body ground - Set HVAC double layer
·

Ignition switch ON

·

Double Layer*2


11 to 14 V
·

Ignition switch ON

·

Single Layer


Below 1 V
F7A-2 (B2AI) - Body ground - Output for driving the motor to switch inlet/outlet B2
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly (fresh/recirculation) operating


Pulse generation
(See waveform 3)
F7A-3 (A2AI) - Body ground - Output for driving the motor to switch inlet/outlet A2
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly (fresh/recirculation) operating


Pulse generation
(See waveform 3)
F7A-4 (A2AO) - Body ground - Output for driving the motor to switch mode A2
·

Ignition switch ON

·

No. 2 air conditioning radiator damper servo sub-assembly (mode switching) operating


Pulse generation
(See waveform 4)
F7A-6 (B2AO) - Body ground - Output for driving the motor to switch mode B2
·

Ignition switch ON

·

No. 2 air conditioning radiator damper servo sub-assembly (mode switching) operating


Pulse generation
(See waveform 4)
F7A-8 (B1AO) - Body ground - Output for driving the motor to switch mode B1
·

Ignition switch ON

·

No. 2 air conditioning radiator damper servo sub-assembly (mode switching) operating


Pulse generation
(See waveform 4)
F7A-9 (A1AI) - Body ground - Output for driving the motor to switch inlet/outlet A1
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly (fresh/recirculation) operating


Pulse generation
(See waveform 3)
F7A-10 (B1AI) - Body ground - Output for driving the motor to switch inlet/outlet B1
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly (fresh/recirculation) operating


Pulse generation
(See waveform 3)
F7A-13 (BAI) - Body ground - Power supply to the motor to switch inlet/outlet Ignition switch ON 11 to 14 V
F7A-16 (A1AO) - Body ground - Output for driving the motor to switch mode A1
·

Ignition switch ON

·

No. 2 air conditioning radiator damper servo sub-assembly (mode switching) operating


Pulse generation
(See waveform 4)
F7A-21 (SHUNT2) - Body ground - Set HVAC double layer
·

Ignition switch ON

·

Double Layer*2


11 to 14 V
·

Ignition switch ON

·

Single Layer


Below 1 V
F7A-22 (B1RU) - Body ground - Output for driving the air mix motor in right upper layer B1
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (upper air mix) operating


Pulse generation
(See waveform 5)
F7A-23 (A2RL) - Body ground - Output for driving the air mix motor in right lower layer A2
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (lower air mix) operating


Pulse generation
(See waveform 6)
F7A-24 (A1RU) - Body ground - Output for driving the air mix motor in right upper layer A1
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (upper air mix) operating


Pulse generation
(See waveform 5)
F7A-25 (B2RL) - Body ground - Output for driving the air mix motor in right lower layer B2
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (lower air mix) operating


Pulse generation
(See waveform 6)
F7A-26 (B1RL) - Body ground - Output for driving the air mix motor in right lower layer B1
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (lower air mix) operating


Pulse generation
(See waveform 6)
F7A-27 (A2RU) - Body ground - Output for driving the air mix motor in right upper layer A2
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (upper air mix) operating


Pulse generation
(See waveform 5)
F7A-28 (A1RL) - Body ground - Output for driving the air mix motor in right lower layer A1
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (lower air mix) operating


Pulse generation
(See waveform 6)
F7A-29 (B2RU) - Body ground - Output for driving the air mix motor in right upper layer B2
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (upper air mix) operating


Pulse generation
(See waveform 5)
F7A-32 (BAO) - Body ground - Power supply to the motor to switch mode Ignition switch ON 11 to 14 V
F7A-33 (BRU) - Body ground - Power supply to the air mix motor in right upper layer Ignition switch ON 11 to 14 V
F7A-34 (BRL) - Body ground - Power supply to the air mix motor in right lower layer Ignition switch ON 11 to 14 V
F7A-38 (TEA) - F7A-39 (SGA) - Input No. 1 cooler thermistor
·

Ignition switch ON

·

Evaporator temperature: 0°C (32°F)


0.5 V
·

Ignition switch ON

·

Evaporator temperature: 25°C (77°F)


1.6 V
F7A-39 (SGA) - Body ground - Ground for No. 1 cooler thermistor Always Below 1 V
F7A-40 (BLW) - F72-29 (GND) - Output for driving Blower motor
·

Ignition switch ON

·

Blower switch: Lo


Pulse generation
(See waveform 4)

*1: w/ PTC Heater

*2: w/ Headlight Cleaner System

*3: for LHD

*4: for RHD

*5: for HFC-134a (R134a)

*6: for HFO-1234yf (R1234yf)

*7: w/ Cooler System


a.
E334619N04
0.292,1.542 0.75,1.74 0.458,0.198 10 false GND

Waveform 1:

Item Content
Terminal No. F72-3 (LIN1) - F72-29 (GND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Vehicle Condition Ignition switch ON


b.
E338778N02
2.823,1.219 3.281,1.417 0.458,0.198 10 false GND

Waveform 2:

Item Content
Terminal No. F72-15 (SOL-) - F72-29 (GND)
Tool Setting 5 V/DIV., 1 ms./DIV.
Vehicle Condition
·

Engine running

·

Blower switch: Lo

·

A/C switch: On




c.
E357637N01
2.896,1.208 3.354,1.406 0.458,0.198 10 false GND

Waveform 3:

Item Content
Terminal No. F7A-2 (B2AI) - Body ground
F7A-3 (A2AI) - Body ground
F7A-9 (A1AI) - Body ground
F7A-10 (B1AI) - Body ground
Tool Setting 2 V/DIV., 10 ms./DIV.
Vehicle Condition
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly (fresh/recirculation) operating




d.
E357637N02
2.896,1.208 3.354,1.406 0.458,0.198 10 false GND

Waveform 4:

Item Content
Terminal No. F7A-4 (A2AO) - Body ground
F7A-6 (B2AO) - Body ground
F7A-8 (B1AO) - Body ground
F7A-16 (A1AO) - Body ground
Tool Setting 2 V/DIV., 10 ms./DIV.
Vehicle Condition
·

Ignition switch ON

·

No. 2 air conditioning radiator damper servo sub-assembly (mode switching) operating




e.
E357637N03
2.896,1.208 3.354,1.406 0.458,0.198 10 false GND

Waveform 5:

Item Content
Terminal No. F7A-22 (B1RU) - Body ground
F7A-24 (A1RU) - Body ground
F7A-27 (A2RU) - Body ground
F7A-29 (B2RU) - Body ground
Tool Setting 2 V/DIV., 10 ms./DIV.
Vehicle Condition
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (upper air mix) operating (for LHD)




f.
E357637N04
2.896,1.208 3.354,1.406 0.458,0.198 10 false GND

Waveform 6:

Item Content
Terminal No. F7A-23 (A2RL) - Body ground
F7A-25 (B2RL) - Body ground
F7A-26 (B1RL) - Body ground
F7A-28 (A1RL) - Body ground
Tool Setting 2 V/DIV., 10 ms./DIV.
Vehicle Condition
·

Ignition switch ON

·

No. 1 air conditioning radiator damper servo sub-assembly (lower air mix) operating (for LHD)




g.
E338778N03
2.823,1.208 3.281,1.406 0.458,0.198 10 false GND

Waveform 7:

Item Content
Terminal No. F7A-40 (BLW) - F72-29 (GND)
Tool Setting 2 V/DIV., 1 ms./DIV.
Vehicle Condition
·

Ignition switch ON

·

Blower switch: Lo





AIR CONDITIONING CONTROL ASSEMBLY


E352244N01
3.26,0.25 3.76,0.5 0.5,0.25 3.396,0.271 4.469,0.469 1.073,0.198 10 false F61

HINT:

Check from the rear of the connector while it is connected to the air conditioning control assembly.


Terminal No. (symbol) Wiring Color Terminal Description Condition Specified Condition
F61-2 (LIN1) - Body ground L - Body ground LIN communication Ignition switch ON Pulse generation (See waveform 1)
F61-10 (IG+) - Body ground BE - Body ground Power source (IG) Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
F61-16 (GND) - Body ground W-B - Body ground Ground for air conditioning control assembly Always Below 1 V

a.
E334619N09
0.292,1.542 0.75,1.74 0.458,0.198 10 false GND

Waveform 1:

Item Content
Terminal No. F61-2 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Vehicle Condition Ignition switch ON