Home › Engine / Hybrid System › 8NR-FTS (STARTING) › STARTER (for Valeo Made except Cold Area Specification Vehicles)
RM32H0E _51 Engine / Hybrid System _060199 8NR-FTS STARTING _0295155 STARTER(for Valeo Made except Cold Area Specification Vehicles) G

8NR-FTS STARTING  STARTER(for Valeo Made except Cold Area Specification Vehicles)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A397114

Remove the nut, and disconnect the field coil lead wire from terminal C.


ii.
A397115C01
1.219,1.51 1.635,1.094 false 1.469,1.531 1.469,2.615 true 1.76,1.563 1.854,2.458 1.854,2.458 2.021,2.458 true 2.719,2.469 2.719,2.823 false 2.063,2.354 2.375,2.51 0.313,0.156 10 false *a 1.396,2.646 1.708,2.802 0.313,0.156 10 false *b 2.646,2.833 2.958,2.99 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Moves outward


Connect a battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



b.

Perform a hold-in test.

i.
A397116C01
1.51,1.552 1.51,2.729 true 1.76,1.563 1.854,2.479 1.854,2.479 2.021,2.479 true 2.729,2.469 2.729,2.823 false 2.073,2.375 2.385,2.531 0.313,0.156 10 false *a 1.438,2.76 1.75,2.917 0.313,0.156 10 false *b 2.646,2.833 2.958,2.99 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal C
*c Starter Body
V100135

Disconnect


While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from terminal C. Check that the clutch pinion gear does not return inward.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.

Perform a return test.

i.
A397117C01
1.74,1.552 1.74,2.729 true 2.729,2.458 2.729,2.781 false 1.656,2.74 1.969,2.896 0.313,0.156 10 false *a 2.656,2.823 2.969,2.979 0.313,0.156 10 false *b
*a Terminal 50
*b Starter Body
V100135

Disconnect
V100136

Returns inward


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, replace the magnet starter switch assembly.



d.

Perform a no-load performance test.

i.
A397114

Connect the field coil lead wire to terminal C with the nut. Make sure that the field coil lead wire is not grounded.

Torque:
10.6 N*m (108 kgf*cm, 8 ft.*lbf)


ii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iii.
A397118C01
1.406,1.302 0.927,1.302 false 1.771,2.646 1.771,1.573 true 2.74,2.781 2.74,2.448 false 1.688,2.667 2,2.823 0.313,0.156 10 false *a 0.74,1.198 1.052,1.354 0.313,0.156 10 false *b 2.667,2.802 2.979,2.958 0.313,0.156 10 false *c
*a Terminal 50
*b Terminal 30
*c Starter Body
V100135

Rotates


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



iv.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive (+) terminal - Terminal 30 - Terminal 50 11.5 V Below 90 A


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

HINT:

If there is no continuity between any segments, replace the starter armature assembly.


a.

Check the commutator appearance.

If the surface is dirty or burnt, restore it with sandpaper (No. 400) or on a lathe.


b.

Check the commutator for an open circuit.

i.
A444811C01
2,0.344 2.167,0.854 true 1.833,0.219 2.021,0.406 0.188,0.188 10 false *a
*a Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator for a short circuit.

i.
A444812C01
2.073,0.313 1.594,0.688 true 2.125,1.74 1.927,1.385 true 2.156,1.677 2.365,1.875 0.208,0.198 10 false *a 2.125,0.208 2.708,0.385 0.583,0.177 10 false *b
*a Segment
*b Starter Armature Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A058584C12
2.75,0.948 2.927,1.146 0.177,0.198 10 false *a
*a Length


Using a vernier caliper, measure the commutator.

Standard length:

3.1 mm (0.122 in.)


Maximum length:

3.5 mm (0.138 in.)


If the length is more than the maximum, replace the starter armature assembly.


Hide 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the brush length.

i.
A296793C04
2.859,0.71 3.081,0.920 0.222,0.211 10 *a
*a Length


Using a vernier caliper, measure the brush length.

Standard length:

15.2 mm (0.598 in.)


Minimum length:

12.2 mm (0.480 in.)


If the length is less than the minimum, replace the starter commutator end frame assembly.



b.

Check the brush insulation.

i.
A296794C02
2.385,0.771 2.813,0.427 2.813,0.427 2.656,1.073 true 2.302,1.313 1.49,1.688 1.49,1.688 2.073,0.948 true 2.844,0.292 3.052,0.448 0.208,0.156 10 false *a 1.281,1.656 1.49,1.813 0.208,0.156 10 false *b
*a Positive (+) Brush
*b Negative (-) Brush


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush - Negative (-) brush Always 10 kΩ or higher


If the result is not as specified, replace the starter commutator end frame assembly.



Hide 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth on the planetary gears, and the internal gear and pinion gear of the starter center bearing clutch sub-assembly for wear or damage.

If any of the gears is damaged, replace the starter center bearing clutch sub-assembly.


b.
A444813

Insert the starter armature assembly to the starter center bearing clutch sub-assembly.


c.

Check the starter center bearing clutch pinion gear.

i.
A444814C01
0,0 0,0 false
V100135

Free
V100136

Lock


Hold the starter center bearing clutch sub-assembly, rotate the pinion gear clockwise and check that the pinion gear turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter center bearing clutch sub-assembly.



Hide 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A444867

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the repair service starter kit.



b.

Check the pull-in coil for an open circuit.

i.
A444816C01
1.927,1.365 2.281,1.708 true 1.646,1.313 1.271,0.844 true 2.313,1.635 2.531,1.813 0.219,0.177 10 false *a 1.073,0.74 1.292,0.917 0.219,0.177 10 false *b
*a Terminal 50
*b Terminal C


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the repair service starter kit.



c.

Check the holding coil for an open circuit.

i.
A444817C01
2.448,0.698 2.677,0.354 true 2.219,1.844 1.906,1.354 true 2.729,0.25 3.042,0.448 0.313,0.198 10 false *b 2.281,1.76 2.594,1.958 0.313,0.198 10 false *a
*a Terminal 50
*b Magnet Switch Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Magnet switch body Always Below 2 Ω


If the result is not as specified, replace the repair service starter kit.