Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › ANTENNA CORD › 2018.05–2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0303547 ANTENNA CORD A

NAVIGATION / MULTI INFO DISPLAY  ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101Q 1.INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/ FM Sub-antenna)

a.
E353813

Engage the clamp and 2 grommets to install the No. 4 antenna cord sub-assembly.


b.

Connect the connector.


Hide 64790B 2.INSTALL BACK DOOR TRIM UPPER PANEL ASSEMBLY (w/ FM Sub-antenna)

Hide 86101D 3.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.

w/o FM Sub-antenna:

i.
E396316C01
0.25,2.25 3.25,3.25 3,1 2.229,0.813 2.49,0.667 true 0.781,1.271 1.104,1.385 true 2.25,2.25 2.25,3.25 false 1.167,2.25 1.167,3.25 false 2.49,0.563 2.729,0.76 0.24,0.198 10 true *a 0.542,1.177 0.781,1.375 0.24,0.198 10 true *b 0.302,2.271 0.615,2.49 0.313,0.219 12 false *A 1.25,2.281 1.563,2.5 0.313,0.219 12 false *B 2.333,2.281 2.646,2.5 0.313,0.219 12 false *C
*A for Type A
*B for Type B
*C for Type C
*a Guide
*b Clamp


Engage the clamp and guide to temporarily install the No. 3 antenna cord sub-assembly.


ii.

Install the bolt.

Torque:
for Type A : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for Type C : 10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.
E353809

Engage the clamps install the No. 3 antenna cord sub-assembly.


iv.

Connect the connector.



b.

w/ FM Sub-antenna:

i.
E396317C01
0.417,2.25 1.583,3.333 1.167,1.083 2,2.25 3.167,3.333 1.167,1.083 2.125,0.906 2.375,0.75 true 0.719,1.385 1.115,1.521 true 0.458,2.26 0.833,2.5 0.375,0.24 12 false *A 2.042,2.26 2.417,2.5 0.375,0.24 12 false *B 2.375,0.646 2.583,0.854 0.208,0.208 10 true *a 0.51,1.26 0.719,1.469 0.208,0.208 10 true *b
*A for Type A
*B for Type B
*a Guide
*b Clamp


Engage the clamp and guide to temporarily install the No. 3 antenna cord sub-assembly.


ii.

Install the bolt.

Torque:
for Type A : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Connect the connector of the floor wire.


iv.
E353809

Engage the clamps install the No. 3 antenna cord sub-assembly.


v.

Connect the connector.


vi.

Connect the connector of the No. 4 antenna cord sub-assembly.



Hide 86101R 4.INSTALL NO. 5 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)

a.
E353808

Engage the clamp to install the No. 5 antenna cord sub-assembly.


b.

Connect the connector.


Hide 86101J 5.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

Type A:

i.

Remove the old double-sided tape from the roof headlining.

E353817C03
2,1.25 2.667,2.25 0.667,1 4.125,1.094 4.344,1.354 true 2.667,1.75 3,1.75 true 4.396,1.354 4.625,1.563 0.229,0.208 10 true *a 3.083,1.646 3.313,1.854 0.229,0.208 10 true *A
*A w/ Digital Audio Broadcasting Antenna - -
*a Marking - -
V100144

Double-sided Tape
V100136

Front



ii.

Prepare an appropriate amount of new double-sided tape.

HINT:

Be careful not to touch the adhesive surface.



iii.

Apply the double-sided tape to the roof headlining while aligning the tape with the markings on the roof headlining.


iv.

Peel off the release paper from the double-sided tape.


v.

Engage the No. 2 antenna cord sub-assembly to the notch of the roof headlining.

E359078C05
2.406,2.271 3.156,3.354 0.75,1.083 2.083,1.229 2.469,1.052 true 2.885,0.979 3.333,0.771 true 4.583,1.354 4.885,1.448 true 6.583,0.656 6.479,0.958 true 6.958,0.708 6.573,1.063 true 6.708,1.854 6.375,1.021 true 6.417,2.594 5.906,2.427 true 2.958,2.365 3.333,2.365 true 3.156,2.802 3.469,2.802 true 2.854,2.354 3,1.75 true 3.365,0.604 3.677,0.802 0.313,0.198 10 false *a 1.885,1.135 2.198,1.333 0.313,0.198 10 false *e 3.01,1.635 3.323,1.833 0.313,0.198 10 false *d 3.396,2.25 3.604,2.448 0.208,0.198 10 true *g 3.521,2.677 3.781,2.917 0.26,0.24 12 true *A 4.385,1.208 4.698,1.406 0.313,0.198 10 false *d 6.458,2.552 6.667,2.75 0.208,0.198 10 true *g 6.729,1.906 7.042,2.104 0.313,0.198 10 false *b 6.927,0.531 7.156,0.719 0.229,0.188 10 false *c 6.563,0.448 6.792,0.635 0.229,0.188 10 false *f
*A w/ Digital Audio Broadcasting Antenna - -
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Protrusion *f Edge of the roof headlining
*g Adjustment Area - -
V100136

Front - -



vi.

Engage the clamp.


vii.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.


viii.

Install the No. 2 antenna cord sub-assembly on the double-sided tape of the roof headlining.

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




ix.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the edge of roof headlining on the roof headlining and secure the No. 2 antenna cord sub-assembly with the adhesive tape (A) as shown in the illustration.

NOTICE:

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.



x.

Apply the 2 adhesive tapes (B) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




b.

Type B:

i.

Engage the No. 2 antenna cord sub-assembly to the notch of the roof headlining.

E353819C05
2.417,2.313 3.052,3.375 0.635,1.063 2.865,0.969 2.969,0.813 true 2.156,1.188 2.479,1.083 true 4.667,1.365 4.833,1.49 true 1.042,2.365 1.24,1.823 true 1.031,2.771 1.313,2.604 true 2.021,2.177 2.771,2.375 true 2.896,2.573 3.375,2.49 true 2.802,2.573 3.271,3.292 3.271,3.292 2.792,2.938 true 2.375,2.031 3.292,1.656 3.292,1.656 2.708,2.063 true 2.948,2.083 3.292,1.646 3.292,1.646 3.115,2.146 true 3.292,1.667 3.479,2.115 true 4.229,2.313 4.656,2.781 4.656,2.781 3.875,2.281 true 5.083,2.375 4.667,2.781 4.667,2.781 4.604,2.323 true 4.698,2.781 5.563,2.302 true 5.896,2.427 6.417,2.667 true 6.354,1.063 6.677,1.667 true 6.49,0.958 6.615,0.604 true 6.573,1.073 6.75,0.854 true 3.052,2.792 3.344,2.792 true 2.958,0.635 3.271,0.833 0.313,0.198 10 false *a 2,1.146 2.229,1.344 0.229,0.198 10 false *f 1.271,1.646 1.5,1.844 0.229,0.198 10 false *j 0.865,2.719 1.094,2.917 0.229,0.198 10 false *i 1.885,2.073 2.063,2.26 0.177,0.188 10 true *k 3.438,2.385 3.615,2.573 0.177,0.188 10 true *h 3.323,3.302 3.5,3.49 0.177,0.188 10 true *e 4.604,2.813 4.781,3 0.177,0.188 10 true *d 6.479,2.646 6.656,2.833 0.177,0.188 10 false *k 6.667,1.708 6.896,1.906 0.229,0.198 10 false *b 6.74,0.698 6.969,0.896 0.229,0.198 10 false *c 6.604,0.385 6.833,0.583 0.229,0.198 10 false *g 4.469,1.229 4.698,1.427 0.229,0.198 10 false *d 3.229,1.448 3.406,1.635 0.177,0.188 10 false *d 3.406,2.698 3.646,2.917 0.24,0.219 12 true *A
*A w/ Digital Audio Broadcasting Antenna - -
*a Marking Tape (A) *b Marking Tape (B)
*c Adhesive Tape (A) *d Adhesive Tape (B)
*e Adhesive Tape (C) *f Protrusion
*g Edge of the roof headlining *h Marking (B)
*i Clamp *j Notch
*k Adjustment Area - -
V100136

Front - -



ii.

Engage the clamp.


iii.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.


iv.

Install the No. 2 antenna cord sub-assembly on the butyl tape of the roof headlining.

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




v.

Install the No. 2 antenna cord sub-assembly on the butyl tape of the roof headlining from the clamp to the marking (B).

NOTICE:
·

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

·

Make sure the No. 2 antenna cord assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.




vi.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the edge of roof headlining on the roof headlining and secure the No. 2 antenna cord sub-assembly with the adhesive tape (A) as shown in the illustration.

NOTICE:

Make sure that there are no gaps between the roof headlining and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.



vii.

Apply the 11 adhesive tapes (B) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.



viii.

Apply the 2 adhesive tapes (C) as shown in the illustration to secure the No. 2 antenna cord subassembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




Hide 86101 7.INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

Engage the clamps to install the antenna cord sub-assembly.

E353801


b.

Connect the connector.


Hide 86101 8.INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

Engage the clamps to install the antenna cord sub-assembly.

E353804


b.

Connect the connector.


Hide 55086 9.INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)

Hide 55084E 10.INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

Hide 55401E 11.INSTALL INSTRUMENT PANEL SAFETY PAD