Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMMT Made) › from 2018.05
RM32H0E _54 Brake _060042 BRAKE (REAR) _0358313 REAR BRAKE(for TMMT Made) A

BRAKE (REAR)  REAR BRAKE(for TMMT Made)  REASSEMBLY  


PROCEDURE

Hide 1.TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG

a.

Temporarily install the rear disc brake bleeder plug to the rear disc brake cylinder assembly.

HINT:

Fully tighten the rear disc brake bleeder plug after bleeding the system.



Hide 31478C 2.INSTALL REAR DISC BRAKE BLEEDER PLUG CAP

a.

Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.


Hide 3.INSTALL PISTON SEAL

a.
C399550C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply lithium soap base glycol grease to the entire circumference of a new piston seal.


b.

Install the piston seal to the rear disc brake cylinder assembly.

NOTICE:
·

Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.

·

Do not allow the nut to rotate. If the nut is accidentally allowed to rotate, return it to its original position.




Hide 4.INSTALL REAR DISC BRAKE PISTON

a.
C399551C01
0.49,1.667 0.823,1.667 false 0.604,2.781 0.938,2.781 false 0.292,1.583 0.604,1.781 0.313,0.198 10 false *1 0.417,2.698 0.729,2.896 0.313,0.198 10 false *2
*1 Cylinder Boot
*2 Rear Disc Brake Piston
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.


b.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake piston.


c.

Install the cylinder boot to the rear disc brake piston.


d.
C399552C01
2.979,0.615 3.146,0.219 3.146,0.219 2.552,0.583 true 2.979,1.083 2.427,1.333 2.427,1.333 2.552,1.073 true 3.167,0.115 3.417,0.313 0.25,0.198 10 false *a 2.302,1.302 2.458,1.5 0.156,0.198 10 false A
*a Indentations


Install the seal portion of the cylinder boot into the groove portion of the rear disc brake cylinder.

NOTICE:

Securely install the cylinder boot to the groove of the rear disc brake cylinder.



e.

Install the rear disc brake piston to the rear disc brake cylinder assembly.

NOTICE:
·

Install the rear disc brake cylinder LH so that its portions marked (A) fit into the indentations of the rear disc brake piston.

·

Do not forcibly install the rear disc brake piston into the rear disc brake cylinder assembly.




f.

Install the rear disc brake piston to the rear disc brake cylinder assembly.


g.
C399995C01
2.792,0.74 2.969,0.573 false 2.135,0.604 2.354,0.49 false 3.063,1.052 2.875,1.198 true 3,0.469 3.313,0.625 0.313,0.156 10 false *1 2.385,0.406 2.698,0.563 0.313,0.156 10 false *2 3.083,0.938 3.396,1.094 0.313,0.156 10 false *3
*1 Cylinder Boot
*2 Rear Disc Brake Piston
*3 Rear Disc Brake Cylinder Assembly


Make sure that the cylinder boot is securely installed into the groove of the rear disc brake cylinder and rear disc brake piston.