83100
1.INSPECT COMBINATION METER ASSEMBLY
Check speedometer operation
The combination meter assembly receives the vehicle speed signal from the brake actuator assembly (skid control ECU) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the brake actuator assembly (skid control ECU) because it is the source of the vehicle speed signal.
Data List values of the brake actuator assembly (skid control ECU) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC/EPB/EPB / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| Vehicle Speed |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 17.5 to 21.5 |
| 40 | 38.0 to 42.0 |
| 60 | 58.0 to 63.0 |
| 80 | 78.0 to 84.0 |
| 100 | 98.5 to 104.5 |
| 120 | 119.0 to 125.0 |
| 140 | 139.0 to 146.0 |
| 160 | 159.0 to 167.0 |
| 180 | 179.0 to 188.0 |
| 200 | 199.0 to 209.0 |
| 220 | 219.0 to 230.0 |
| GTS Indication (km/h) | Acceptable Range (km/h) |
|---|---|
| 20 | 20.3 to 24.3 |
| 40 | 40.6 to 44.6 |
| 60 | 60.9 to 64.9 |
| 80 | 81.2 to 85.2 |
| 100 | 101.5 to 105.5 |
| 120 | 121.8 to 125.8 |
| 140 | 142.1 to 146.1 |
| 160 | 162.4 to 166.4 |
| 180 | 182.7 to 186.7 |
| 200 | 203.0 to 207.0 |
| 220 | 223.3 to 227.3 |
| GTS Indication (mph) | Acceptable Range (mph) |
|---|---|
| 20 | 20.0 to 23.0 |
| 40 | 40.0 to 43.5 |
| 60 | 60.0 to 64.0 |
| 80 | 80.0 to 84.5 |
| 100 | 100.0 to 105.0 |
| 120 | 120.0 to 125.5 |
| 140 | 140.0 to 146.0 |
Speedometer reading is within the acceptable range at each vehicle speed.
| Tester Display |
|---|
| Vehicle Speed |
Inspect tachometer
Warm up the engine.
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List. (for 8NR-FTS)
Enter the following menus: Powertrain / Engine and ECT / Data List. (for 3ZR-FAE)
Read the Data List according to the display on the GTS. (for 8NR-FTS)
| Tester Display | Measurement Item | Range | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | ·
for 8NR-FTS with CVT: 680 to 780 rpm: Idling with warm engine ·
for 8NR-FTS with Manual Transaxle: 600 to 700 rpm: Idling with warm engine |
- | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Tester Display |
|---|
| Engine Speed |
| GTS Indication (rpm) | Acceptable Range (rpm)
Data in ( ) is for Reference |
|---|---|
| 700 | 630 to 770 |
| 1000 | (900 to 1100) |
| 2000 | (1850 to 2150) |
| 3000 | 2800 to 3200 |
| 4000 | (3800 to 4200) |
| 5000 | 4800 to 5200 |
| 6000 | (5750 to 6250) |
| 7000 | 6700 to 7300 |
| 8000 | (7700 to 8300) |
Tachometer reading is within the acceptable range at each engine speed.
Read the Data List according to the display on the GTS. (for 3ZR-FAE)
| Tester Display | Measurement Item | Range | Normal Condition | Reference Value | Diagnostic Note |
|---|---|---|---|---|---|
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 710 to 810 rpm: Idling with warm engine | - | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Tester Display |
|---|
| Engine Speed |
| GTS Indication (rpm) | Acceptable Range (rpm)
Data in ( ) is for Reference |
|---|---|
| 700 | 630 to 770 |
| 1000 | (900 to 1100) |
| 2000 | (1850 to 2150) |
| 3000 | 2800 to 3200 |
| 4000 | (3800 to 4200) |
| 5000 | 4800 to 5200 |
| 6000 | (5750 to 6250) |
| 7000 | 6700 to 7300 |
| 8000 | (7700 to 8300) |
Tachometer reading is within the acceptable range at each engine speed.
Check LED illumination (LED check)
Check the illumination function of the warning or indicator lights listed below when turning the ignition switch ON.
| Warning or Indicator Light | Control ECU | Specified Condition |
|---|---|---|
| Brake warning light | Brake actuator assembly (Skid control ECU) | Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON. |
| VSC OFF indicator light | Brake actuator assembly (Skid control ECU) | |
| Slip indicator light | Brake actuator assembly (Skid control ECU) | |
| ABS warning light | Brake actuator assembly (Skid control ECU) | |
| Tire pressure warning light*1 | Tire pressure warning and ECU receiver | |
| PCS warning light*2 | Millimeter wave radar sensor assembly | |
| Automatic high beam indicator light*2 | Main body ECU (Multiplex network body ECU) | |
| EPB indicator light | Brake actuator assembly (Skid control ECU) | |
| EPB-Auto OFF indicator light*3 | Brake actuator assembly (Skid control ECU) | |
| EPB warning light | Brake actuator assembly (Skid control ECU) | |
| Brake hold warning light*4 | Brake actuator assembly (Skid control ECU) | |
| Stop and start off indicator light*5 | Engine stop and start ECU | |
| High beam indicator light | Main body ECU (Multiplex network body ECU) | |
| BSM indicator light*6 | Blind spot monitor sensor LH (B) | |
| RCTA indicator light*6 | Blind spot monitor sensor LH (B) | |
| SRS warning light | Airbag sensor assembly | Warning light comes on for about 6 seconds after turning the ignition switch to ON. |
| Charge warning light | ECM | Warning light comes on when the ignition switch to ON. |
| Engine stop and start ECU*4 | ||
| MIL (Check engine warning light) | ECM | |
| EPS warning light | Power steering ECU assembly | |
| IPA indicator light*7 | Clearance warning ECU assembly |
*1: w/ Tire Pressure Warning System
*2: w/ Toyota Safety Sense
*3: for Manual Transaxle
*4: for Monochrome TFT Type
*5: w/ Stop and Start System
*6: w/ Blind Spot Monitor System
*7: w/ TOYOTA Parking Assist-sensor System