Home › Engine / Hybrid System › 8NR-FTS (EMISSION CONTROL) › VACUUM REGULATING VALVE › from 2018.05
RM32H0E _51 Engine / Hybrid System _060038 8NR-FTS EMISSION CONTROL _0294115 VACUUM REGULATING VALVE G

8NR-FTS EMISSION CONTROL  VACUUM REGULATING VALVE  INSPECTION  


PROCEDURE

Hide 25819 1.INSPECT VACUUM REGULATING VALVE ASSEMBLY (w/ Differential Pressure Sensor)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.1 to 12.5 Ω


If the result is not as specified, replace the vacuum regulating valve assembly.


b.

Check the operation of the vacuum regulating valve assembly.

i.
A427001C01
1.542,0.771 1.354,0.615 false 1.802,1.292 1.76,0.958 false 1.708,1.365 2.021,1.563 0.313,0.198 10 false *a 1.156,0.458 1.469,0.656 0.313,0.198 10 false *b 0.823,1.802 1.135,2 0.313,0.198 10 false *c
*a Port (E)
*b Port (F)
*c Air


Using a vacuum pump, apply a vacuum of 67 kPa (503 mmHg, 19.8 in. Hg) to the port (F) and check that the vacuum regulating valve assembly operates normally.


ii.

Check that air flows from the filter when air is blown into the port (E).

HINT:

When air is blown into the port (E), the vacuum of the port (F) decreases.



iii.
A427002C01
0.979,1.25 0.958,0.948 false 0.885,0.667 0.698,0.469 false 0.927,1.26 1.24,1.458 0.313,0.198 10 false *a 0.573,0.281 0.885,0.479 0.313,0.198 10 false *b 0.156,1.833 0.469,2.031 0.313,0.198 10 false *c
*a Port (E)
*b Port (F)
*c Air


Apply battery voltage between the terminals, and check that air flows from the port (F) when air is blown into the port (E).



Hide 25819 2.INSPECT VACUUM REGULATING VALVE ASSEMBLY (w/o Differential Pressure Sensor)

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.1 to 12.5 Ω


If the result is not as specified, replace the vacuum regulating valve assembly.


b.

Check the operation of the vacuum regulating valve assembly.

i.
A328288C03
1.063,1.625 1.396,1.625 true 1.552,1.583 2.104,2.01 2.104,2.01 2.25,2.01 true 0.875,1.521 1.073,1.719 0.198,0.198 10 false *b 2.281,1.917 2.49,2.135 0.208,0.219 10 false *a 1.74,0.042 1.99,0.292 0.25,0.25 10 false *c
*a Port (E)
*b Port (F)
*c Air


Using a vacuum pump, apply a vacuum of 67 kPa (503 mmHg, 19.8 in. Hg) to the port (F) and check that the vacuum regulating valve assembly operates normally.


ii.

Check that air flows from the filter when air is blown into the port (E).

HINT:

When air is blown into the port (E), the vacuum of the port (F) decreases.



iii.
A328289C04
1.385,1.635 1.875,1.99 1.875,1.99 2.104,1.99 true 0.813,1.604 1.25,1.604 true 2.146,1.896 2.333,2.063 0.188,0.167 10 false *a 0.615,1.542 0.802,1.708 0.188,0.167 10 false *b 1.542,0.094 1.729,0.302 0.188,0.208 10 false *c
*a Port (E)
*b Port (F)
*c Air


Apply battery voltage between the terminals, and check that air flows from the port (F) when air is blown into the port (E).