Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM › from 2018.05
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0298220 DYNAMIC TORQUE CONTROL AWD SYSTEM J

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  AWD Warning Light Remains ON  


DESCRIPTION

The 4WD ECU assembly is connected to the combination meter assembly via the CAN communication system.

If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control AWD system, the warning message is displayed on the multi-information display in the combination meter assembly.


WIRING DIAGRAM

C367133E01
0.604,0.698 2.604,0.896 2,0.198 10 false Multi-information Display 0.479,2.25 2.542,2.583 2.063,0.333 10 false Combination Meter Assembly 3.938,1.969 5.25,2.281 1.313,0.313 10 false ECU-IG1 NO. 2 5.729,3.292 7.146,3.604 1.417,0.313 10 false 4WD ECU Assembly 5.74,3.104 6.813,3.302 1.073,0.198 10 false M77 5.75,1.719 6.167,1.917 0.417,0.198 10 false 3 5.76,2.604 6.177,2.802 0.417,0.198 10 false 4 5.958,1.813 6.375,2.01 0.417,0.198 10 false IG1 5.958,2.708 6.375,2.906 0.417,0.198 10 false GND 0.833,4.24 2.896,4.573 2.063,0.333 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM AND DYNAMIC TORQUE CONTROL AWD SYSTEM)
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Check if the dynamic torque control AWD system DTC is output.

Click here

Chassis > Four Wheel Drive > Trouble Codes
50001 118

Result:
Result Proceed to
Neither CAN communication system DTC nor dynamic torque control AWD system DTC is output A
CAN communication DTC is output B
Dynamic torque control AWD system DTC is output C


HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



A

2.CHECK IF 4WD ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (DYNAMIC TORQUE CONTROL AWD SYSTEM)

2.CHECK IF 4WD ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the 4WD ECU assembly connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C64
2.417,0.083 2.917,0.333 0.5,0.25 1.938,1.927 2.24,1.927 2.24,1.927 2.333,1.177 true 1.677,1.854 2.021,2.052 0.344,0.198 10 false IG1 2.531,0.094 2.844,0.292 0.313,0.198 10 false M77 0.083,0.094 0.396,0.25 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M77-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C270074C65
2.417,0.083 2.917,0.333 0.5,0.25 2.167,1.917 2.417,1.917 2.417,1.917 2.583,1.167 true 1.833,1.833 2.177,2.031 0.344,0.198 10 false GND 2.531,0.094 2.844,0.292 0.313,0.198 10 false M77 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M77-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (AWD WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (AWD WARNING LIGHT)
a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


g.

According to the display on the GTS, read the Data List.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
4WD Warning Light AWD warning (multi-information display) OFF or ON OFF: Warning off
ON: Warning on
-
Chassis > Four Wheel Drive > Data List
Tester Display
4WD Warning Light
50003 118 7

h.

Check the GTS display condition of the AWD warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B