Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › CYLINDER BLOCK › from 2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0294294 CYLINDER BLOCK A

8NR-FTS ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 11445 1.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A355421

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.


Hide 12211A 2.REMOVE NO. 1 VENTILATION CASE

a.
A451377

Remove the 8 bolts.


b.
A451374C01
0.875,2.74 1.708,3.177 1.708,3.177 2.521,2.771 true 1.625,3.24 1.938,3.396 0.313,0.156 10 false *a
*a Protective Tape


Remove the No. 1 ventilation case by prying between the No. 1 ventilation case and cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and No. 1 ventilation case.



c.
A355859

Remove the 2 oil separator gaskets from the case separator.


d.
A352673

Remove the 2 bolts and case separator from the No. 1 ventilation case.


Hide 3.REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.
A352878C01
0.76,0.677 1.417,0.302 true 1.469,0.219 1.781,0.375 0.313,0.156 10 false *a
*a Paint Mark


Place a paint mark across each corresponding connecting rod and connecting rod bearing cap.

HINT:

The paint marks are used to ensure that the same parts are installed in the same combination to their original locations.



b.
A352879N01
1.25,0.979 1.688,0.979 false 0.969,0.917 1.427,1.115 0.458,0.198 10 false SST

Using SST, remove the 8 connecting rod bolts from the connecting rod bearing caps.

SST
09205-16011  


c.
A352880

Using the 2 removed connecting rod bolts, remove the 4 connecting rod bearing caps with lower connecting rod bearings by wiggling each connecting rod cap back and forth.

HINT:

Keep the lower connecting rod bearing installed to the connecting rod cap.



d.

Push out the 4 piston sub-assembly with pins with connecting rods and connecting rod bearings through the top of the cylinder block sub-assembly.

HINT:
·

Keep the connecting rod bearing, connecting rod and connecting rod bearing cap together.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the 8 connecting rod bearings from the 4 connecting rods and 4 connecting rod bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13411 5.REMOVE CRANKSHAFT

a.
A352881N01
2.792,0.344 2.948,0.542 0.156,0.198 10 true 1 2.802,1.823 2.958,2.021 0.156,0.198 10 true 2 0.75,0.365 0.906,0.563 0.156,0.198 10 true 3 0.729,1.823 0.885,2.021 0.156,0.198 10 true 4 2.281,0.354 2.438,0.552 0.156,0.198 10 true 5 1.25,0.354 1.406,0.552 0.156,0.198 10 true 7 2.281,1.813 2.438,2.01 0.156,0.198 10 true 6 1.75,1.823 1.906,2.021 0.156,0.198 10 true 9 1.25,1.813 1.406,2.01 0.156,0.198 10 true 8 1.771,0.354 2.167,0.542 0.396,0.188 10 true 10

Uniformly loosen and remove the 10 crankshaft bearing cap set bolts in several steps in the order shown in the illustration.


b.
A352882

Using the 2 removed crankshaft bearing cap set bolts, remove the 5 No. 1 crankshaft bearing caps from the cylinder block sub-assembly by wigging each crankshaft bearing cap back and forth.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



c.

Remove the crankshaft from the cylinder block sub-assembly.


Hide 11711 6.REMOVE CRANKSHAFT BEARING

a.
A352883

Remove the 5 upper crankshaft bearings from the cylinder block sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.
A352884

Remove the 5 lower crankshaft bearings from the 5 No. 1 crankshaft bearing caps.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 11791 7.REMOVE UPPER CRANKSHAFT THRUST WASHER

a.
A352885

Remove the 2 upper crankshaft thrust washers from the cylinder block sub-assembly.


Hide 13011 8.REMOVE PISTON RING SET

a.
A352886

Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring from the piston.


b.

Remove the oil ring expander, upper side rail and lower side rail from the piston by hand.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13101 9.REMOVE PISTON SUB-ASSEMBLY WITH PIN

a.
A352887

Using a screwdriver, pry out the piston pin hole snap ring from the piston.

NOTICE:
·

Do not remove the piston pin hole snap ring (rear side) unless it is being replaced.

·

Be careful not to damage the piston when removing the piston pin hole snap ring (rear side).




b.
A194886

Gradually heat the piston to approximately 80°C (176°F).

CAUTION:

Be sure to wear protective gloves.



c.
A194887

Using a brass bar and a hammer, lightly tap out the piston pin and remove the connecting rod.

HINT:
·

The piston and piston pin are a matched set.

·

Arrange the removed parts in such a way that they can be reinstalled to their original locations.




Hide 15708 10.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A352889

Using a 5 mm hexagon socket wrench, remove the 4 bolts and 4 No. 1 oil nozzle sub-assemblies from the cylinder block sub-assembly.


Hide 13516B 11.REMOVE OIL JET

a.
A394369

Remove the oil jet from the cylinder block sub-assembly.