Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0404351 PANORAMIC VIEW MONITOR SYSTEM D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  SYSTEM DESCRIPTION  


COMMUNICATION SYSTEM OUTLINE


a.

CAN communication system

i.

The panoramic view monitor system uses CAN communication for data communications between the parking assist ECU and each ECU.


ii.

If a problem occurs in the CAN communication line, the parking assist ECU outputs a CAN communication malfunction DTC. (To check, use the GTS.)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR


iii.

If a problem occurs in the CAN communication line, the parking assist ECU outputs a CAN communication malfunction DTC. (To check, use the radio and display receiver assembly diagnosis screen.)

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM


iv.

If a CAN communication line malfunction DTC is output, repair the malfunction in the communication line and troubleshoot the panoramic view monitor system when data communication is normal.


v.

Since the CAN communication line has its own length and route, it cannot be repaired temporarily with a bypass wire, etc.




VIDEO SIGNALS


a.

Video signal circuit

E372768E04
0.177,1.448 2.75,1.781 2.573,0.333 10 false Front Television Camera Assembly 0.198,3.292 3.146,3.865 2.948,0.573 10 false Side Television Camera Assembly LH 0.208,5.188 2.865,5.5 2.656,0.313 10 false Side Television Camera Assembly RH 0.104,7.052 2.979,7.365 2.875,0.313 10 false Rear Television Camera Assembly 0.917,7.969 3.208,8.26 2.292,0.292 10 false : Video Signal (Analog) 0.927,8.406 2.99,8.667 2.063,0.26 10 false : Display Signal Direction 2.99,7.073 4.479,7.604 1.49,0.531 10 false Parking Assist ECU 5.167,3.594 6.875,4.208 1.708,0.615 10 false Radio and Display Receiver Assembly

i.

Video signals from the front television camera assembly are input into the parking assist ECU via analog communication lines (vehicle wire harness).


ii.

Video signals from the side television camera assembly LH are input into the parking assist ECU via analog communication lines (vehicle wire harness).


iii.

Video signals from the side television camera assembly RH are input into the parking assist ECU via analog communication lines (vehicle wire harness).


iv.

Video signals from the rear television camera assembly are input into the parking assist ECU via analog communication lines (vehicle wire harness).


v.

Video signals from the parking assist ECU are input into the radio and display receiver assembly via analog communication lines (vehicle wire harness).



b.

Screen display

i.

Video signals input from each camera are processed in the parking assist ECU and displayed on the radio and display receiver assembly as the panoramic view monitor system screen.




DIAGNOSTIC FUNCTION OUTLINE


a.

This panoramic view monitor system has a diagnostic function displayed in the radio and display receiver assembly. This function enables the calibration (adjustment and verification) of the panoramic view monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM


b.

The panoramic view monitor system can check the following items by using the GTS.

Item Proceed to
DTC (Click here)
Data List / Active Test (Click here)



CALIBRATION


a.

Use the panoramic view monitor system diagnosis screen for calibration and checking of the panoramic view monitor system.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DIAGNOSIS SYSTEM

NOTICE:

Part replacement and work performed during servicing may require calibration of the panoramic view monitor system and other systems.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION