Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060571 PARK ASSIST / MONITORING _0404351 PANORAMIC VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  TERMINALS OF ECU  


PARKING ASSIST ECU


E399010N07
2.854,0.375 3.271,0.625 0.417,0.25 2.896,0.427 3.51,0.625 0.615,0.198 10 false M116

a.

Disconnect the M116 parking assist ECU connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M116-1 (+B) - M116-2 (GND1) L - W-B Power source signal Engine switch off 11 to 14 V
M116-19 (+B2) - M116-2 (GND1) P - W-B Power source signal Engine switch off 11 to 14 V
M116-2 (GND1) - Body ground W-B - Body ground Ground Always Below 1 Ω
M116-20 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
M116-21 (IG) - M116-2 (GND1) BE - W-B IG power source signal Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
M116-3 (ACC) - M116-2 (GND1) R - W-B ACC power source signal Engine switch on (ACC) 11 to 14 V
Engine switch off Below 1 V


c.

Reconnect the M116 parking assist ECU connector.


d.

Measure the voltage, resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M116-11 (CV+) - M116-12 (SGND) R - Shield Rear television camera assembly display signal input Engine switch on (IG) with the camera lens of the rear television camera assembly not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the rear television camera assembly covered, blacking out the panoramic image Pulse generation (See waveform 2)
M116-35 (CV-) - M116-2 (GND1) W - W-B Rear television camera assembly ground Always Below 1 Ω
M116-8 (CB+) - M116-2 (GND1) B - W-B Power source to rear television camera assembly Engine switch on (ACC) 5.5 to 7.05 V
M116-30 (RCV+) - M116-23 (RGND) G - W Side television camera assembly RH display signal input Engine switch on (IG) with the camera lens of the side television camera assembly RH not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the side television camera assembly RH covered, blacking out the panoramic image Pulse generation (See waveform 2)
M116-31 (RCV-) - M116-2 (GND1) R - W-B Side television camera assembly RH ground Always Below 1 Ω
M116-6 (RCB+) - M116-23 (RGND) B - W Power source to side television camera assembly RH Engine switch on (ACC) 5.5 to 7.05 V
M116-37 (RSW+) - M116-2 (GND1) P - W-B Terminal required by law Panoramic image being displayed 0 to 2 V
Panoramic image not being displayed 5.5 to 7.05 V
M116-12 (SGND) - Body ground Shield - Body ground Rear television camera assembly ground (shield) Always Below 1 Ω
M116-36 (LCV+) - M116-26 (LGND) G - W Side television camera assembly LH display signal input Engine switch on (IG) with the camera lens of the side television camera assembly LH not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the side television camera assembly LH covered, blacking out the panoramic image Pulse generation (See waveform 2)
M116-13 (LCV-) - M116-2 (GND1) R - W-B Side television camera assembly LH ground Always Below 1 Ω
M116-9 (LCB+) - M116-26 (LGND) B - W Power source to side television camera assembly LH Engine switch on (ACC) 5.5 to 7.05 V
M116-33 (BCV+) - M116-24 (BGND) B - W Front television camera assembly display signal input Engine switch on (IG) with the camera lens of the front television camera assembly not covered, displaying the panoramic image Pulse generation (See waveform 1)
Engine switch on (IG) with the camera lens of the front television camera assembly covered, blacking out the panoramic image Pulse generation (See waveform 2)
M116-10 (BCV-) - M116-2 (GND1) R - W-B Front television camera assembly ground Always Below 1 Ω
M116-7 (BCB+) - M116-24 (BGND) B - W Power source to front television camera assembly Engine switch on (ACC) 5.5 to 7.05 V
M116-32 (SGND) - Body ground Shield - Body ground Side television camera assembly RH ground (shield) Always Below 1 Ω
M116-23 (RGND) - Body ground W - Body ground Side television camera assembly RH ground Always Below 1 Ω
M116-14 (SGND) - Body ground Shield - Body ground Side television camera assembly LH ground (shield) Always Below 1 Ω
M116-26 (LGND) - Body ground W - Body ground Side television camera assembly LH ground Always Below 1 Ω
M116-34 (SGND) - Body ground Shield - Body ground Front television camera assembly ground (shield) Always Below 1 Ω
M116-24 (BGND) - Body ground W - Body ground Front television camera assembly ground Always Below 1 Ω
M116-40 (CANH) - Body ground L - Body ground CAN communication signal - -
M116-18 (CANH) - Body ground GR - Body ground CAN communication signal - -
M116-15 (BLSW) - M116-2 (GND1) L - W-B Panoramic view monitor switch switch signal Engine switch on (IG), panoramic view monitor switch not pushed 5.5 to 6.5 V
Engine switch on (IG), panoramic view monitor switch pushed Below 1 V
M116-27 (NS+) - M116-29 (NSG) W - Shield Video signal Engine switch on (IG) and panoramic image being displayed Pulse generation (See waveform 3)
M116-28 (NS-) - M116-2 (GND1) B - W-B Ground Always Below 1 Ω
M116-29 (NSG) - Body ground Shield - Body ground Shield ground Always Below 1 Ω


e.
E265840C32
0.844,2.01 1.125,1.573 true 1.479,1.948 1.229,1.49 true 1.552,4.167 1.271,3.521 true 0.844,4.188 1.146,3.604 true 0.229,0.229 0.542,0.427 0.313,0.198 10 false *a 0.396,1.052 0.76,1.313 0.365,0.26 10 false GND 0.396,3.208 0.76,3.469 0.365,0.26 10 false GND 0.26,2.271 0.625,2.531 0.365,0.26 10 false *b 0.74,4.188 1.104,4.448 0.365,0.26 10 false *c 0.656,1.979 1.021,2.24 0.365,0.26 10 false *c 1.51,1.969 1.875,2.229 0.365,0.26 10 false *d 1.5,4.208 1.865,4.469 0.365,0.26 10 false *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Reference (Oscilloscope waveform):

HINT:

A waterproof connector is used for the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Measurement terminal
·

M116-11 (CV+) - M116-25 (CGND)

·

M116-36 (LCV+) - M116-26 (LGND)

·

M116-33 (BCV+) - M116-24 (BGND)

·

M116-30 (RCV+) - M116-23 (RGND)


Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.

·

The video waveform is constantly output when the engine switch is on (ACC).




ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Measurement terminal
·

M116-11 (CV+) - M116-25 (CGND)

·

M116-36 (LCV+) - M116-26 (LGND)

·

M116-33 (BCV+) - M116-24 (BGND)

·

M116-30 (RCV+) - M116-23 (RGND)


Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic view monitor system operating

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly, front television camera assembly, side television camera assembly LH or side television camera assembly RH.

·

The video waveform is constantly output when the engine switch is on (ACC).




iii.
E336160C03
0.865,2.729 1.115,2.26 true 1.563,2.75 1.25,2.125 true 0.229,0.313 0.542,0.51 0.313,0.198 10 false *a 0.271,1.594 0.688,1.792 0.417,0.198 10 false GND 1.625,2.771 1.938,2.969 0.313,0.198 10 false *c 0.698,2.74 1.01,2.938 0.313,0.198 10 false *b
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Synchronization Signal
*c Video Waveform


Waveform 3

Item Content
Measurement terminal M116-27 (NS+) - M116-28 (NS-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic image being displayed

HINT:

The video waveform changes according to the image sent by the parking assist ECU.





RADIO AND DISPLAY RECEIVER ASSEMBLY


E388868E03
3.417,0.333 3.833,0.583 0.417,0.25 3.479,0.385 3.958,0.656 0.479,0.271 10 false F131

a.

Measure the resistance and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F131-9 (CSW+) - Body ground P - Body ground Terminal required by law Panoramic image being displayed 0 to 2 V
Panoramic image not being displayed 5.5 to 7.05 V
F131-28 (V+) - Body ground W - Body ground Video signal Panoramic image being displayed Pulse generation
(Refer to waveform 1)
F131-29 (V-) - Body ground B - Body ground Ground Always Below 1 Ω


b.

Reference (Oscilloscope waveform):

i.
E336160C03
0.865,2.729 1.115,2.26 true 1.563,2.75 1.25,2.125 true 0.229,0.313 0.542,0.51 0.313,0.198 10 false *a 0.271,1.594 0.688,1.792 0.417,0.198 10 false GND 1.625,2.771 1.938,2.969 0.313,0.198 10 false *c 0.698,2.74 1.01,2.938 0.313,0.198 10 false *b
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Synchronization Signal
*c Video Waveform


Waveform 1

Item Content
Measurement terminal F131-28 (V+) - F131-29 (V-)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Panoramic image being displayed

HINT:

The video waveform changes according to the image sent by the parking assist ECU.