Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  U012587  Lost Communication With Multi-axis Acceleration Sensor Module Missing Message  U012987  Lost Communication With Brake System Control Module Missing Message  


DESCRIPTION

The ECM and airbag sensor assembly (yaw rate and acceleration sensor), skid control ECU (brake actuator assembly) send and receive signals via CAN communication.

If a communication error occurs between the ECM, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U012587 Lost Communication With Multi-axis Acceleration Sensor Module Missing Message There is no communication between the ECM and airbag sensor assembly (yaw rate and acceleration sensor) (1 trip detection logic).
·

ECM

·

Airbag sensor assembly (yaw rate and acceleration sensor)

·

CAN Communication System


Does not come on DTC stored SAE Code: U0125
U012987 Lost Communication With Brake System Control Module Missing Message There is no communication between the ECM and skid control ECU (brake actuator assembly) (1 trip detection logic).
·

ECM

·

Brake actuator assembly (skid control ECU)

·

CAN Communication System


Comes on DTC stored SAE Code: U0129

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: U012587 or U012987.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT (DTC U012587 OR U012987)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTC U012587 or U012987 is output A
DTC U012587 or U012987 and other DTCs are output B


HINT:

If any DTCs other than U012587 or U012987 are output, troubleshoot those DTCs first.




A

B