The millimeter wave radar sensor assembly is connected to the forward recognition camera via CAN communication.
The millimeter wave radar sensor assembly operates the pre-collision alarm by sending a buzzer request signal to the pre-collision city buzzer.
If the millimeter wave radar sensor assembly detects a malfunction in the pre-collision city buzzer circuit, it stores DTC C1A4A.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A4A | Skid Control Buzzer Circuit | When the ignition switch to ON and the pre-collision alarm is operating, either of the following conditions is met:
·
A buzzer request signal is sent to the pre-collision city buzzer but the buzzer does not sound for 0.3 seconds or more. ·
A buzzer request signal is not sent to the pre-collision city buzzer but the buzzer sounds for 0.3 seconds or more. |
·
Pre-collision city buzzer ·
Forward recognition camera ·
Millimeter wave radar sensor assembly ·
Wire harness or connector |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | When the ignition switch to ON and the pre-collision alarm is operating. | ○ | ○ |
| Malfunction Status | A buzzer request signal is sent to the pre-collision city buzzer but the buzzer does not sound. | ○ | - |
| A buzzer request signal is not sent to the pre-collision city buzzer but the buzzer sound. | - | ○ | |
| Detection Time | 0.3 seconds | 0.3 seconds | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the millimeter wave radar sensor assembly, always replace it with a new one.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Axis Adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When a malfunction occurs in the communication line to the forward recognition camera, U023A and/or U1002 is output. If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>U1002
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Collision Alarm Buzzer | Pre-collision city buzzer | ON / OFF | Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped |
| Tester Display |
|---|
| PCS Collision Alarm Buzzer |
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Front view of wire harness connector
(to Pre-collision City Buzzer) |
Disconnect the pre-collision city buzzer connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F54-2 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
Connect the F54 pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F54 pre-collision city buzzer connector.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F54-1 (BZ) - R5-8 (BZ) | Always | Below 1 Ω |
| F54-1 (BZ) or R5-8 (BZ) - Body ground | Always | 10 kΩ or higher |
Connect the R5 forward recognition camera connector.
Connect the F54 pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Collision Alarm Buzzer | Pre-collision city buzzer | ON / OFF | Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped |
| Tester Display |
|---|
| PCS Collision Alarm Buzzer |
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Turn the ignition switch to ON.
Check if the pre-collision city buzzer is sounding.
| Result | Proceed to |
|---|---|
| The pre-collision city buzzer does not sound when the ignition switch to ON | A |
| The pre-collision city buzzer sounds continuously when the ignition switch to ON | B |
A
B
Remove the pre-collision city buzzer.
for LHD: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER(for LHD)>REMOVAL
for RHD: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER (for RHD)>REMOVAL
Inspect the pre-collision city buzzer.
for LHD: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER(for LHD)>INSPECTION
for RHD: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER (for RHD)>INSPECTION
| Result | Proceed to |
|---|---|
| Pre-collision city buzzer is abnormal | A |
| Pre-collision city buzzer is normal | B |
A
B
Replace the pre-collision city buzzer.
for LHD: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER(for LHD)>REMOVAL
for RHD: Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM WARNING BUZZER (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Collision Alarm Buzzer | Pre-collision city buzzer | ON / OFF | Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped |
| Tester Display |
|---|
| PCS Collision Alarm Buzzer |
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Replace the forward recognition camera.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL
Perform Forward Recognition Axis Adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
Perform the Active Test according to the display on the GTS.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
Perform the Active Test for 1 second or more.
Performing the Active Test for 1 second or more causes DTC C1A4A to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Collision Alarm Buzzer | Pre-collision city buzzer | ON / OFF | Test possible with ignition switch to ON
Vehicle condition: Vehicle stopped |
| Tester Display |
|---|
| PCS Collision Alarm Buzzer |
Check for DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1A4A is not output | A |
| DTC C1A4A is output | B |
A
B
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Adjust the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT