Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2019.09
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the airbag sensor assembly (yaw rate and acceleration sensor). If a malfunction in the airbag sensor assembly (yaw rate and acceleration sensor) is determined based on a malfunction signal from the skid control ECU (brake actuator assembly), the ECM stores this DTC.

HINT:
·

The airbag sensor assembly (yaw rate and acceleration sensor) signal is sent to the skid control ECU (brake actuator assembly) via CAN communication.

·

If CAN communication DTCs are output, perform troubleshooting for those DTCs first.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit After the ignition switch is turned ON, the skid control ECU (brake actuator assembly) has detected one of the following conditions, and the ECM has received a diagnostic signal from the skid control ECU (brake actuator assembly) for 3 seconds or more (1 trip detection logic).
·

Output value of the airbag sensor assembly (yaw rate and acceleration sensor) remains at -1.5 G or less, or 1.5 G or more for at least 1.2 seconds.

·

Airbag sensor assembly (yaw rate and acceleration sensor) power source voltage is 4.4 V or less, or 5.6 V or higher, for at 1.2 seconds or more.

·

No signal is detected from the airbag sensor assembly (yaw rate and acceleration sensor) 7 times or more.

·

With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G.

·

An airbag sensor assembly (yaw rate and acceleration sensor) power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more.


·

Airbag sensor assembly (Yaw rate and acceleration sensor)

·

Brake actuator assembly (Skid control ECU)

·

CAN communication system


Does not come on DTC stored

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5
Diagnostic Condition The ignition switch is ON. ○ ○ ○ ○ ○
Malfunction Condition The output value of the airbag sensor assembly (yaw rate and acceleration sensor) remains below -1.5 G or less, or 1.5 G or more for at least 1.2 seconds or more. ○ - - - -
The airbag sensor assembly (yaw rate and acceleration sensor) power source voltage is at 4.4 V or less, or 5.6 V or higher for 1.2 seconds or more. - ○ - - -
No signal from the airbag sensor assembly (yaw rate and acceleration sensor) is detected 7 times or more. - - ○ - -
With the vehicle stopped, the difference between GL1 and GL2 does not become less than 0.4 G within 60 seconds after exceeding 0.6 G. - - - ○ -
An airbag sensor assembly (yaw rate and acceleration sensor) power source voltage malfunction signal is received for at least 10 seconds with the vehicle speed at 3 km/h (1.8 mph) or more. - - - - ○
Duration 3 seconds or more 3 seconds or more 3 seconds or more 3 seconds or more 3 seconds or more
Detection Logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when any one of the above detection patterns is met.


WIRING DIAGRAM

C423061E01
1.042,1.24 1.365,1.458 0.323,0.219 10 false A42 1.031,1.385 2.583,1.833 1.552,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 1.771,0.51 2.292,0.698 0.521,0.188 10 false CANH 1.792,0.938 2.26,1.125 0.469,0.188 10 false CANL 4.927,0.51 5.927,0.896 1,0.385 10 false CANH 4.948,0.948 5.333,1.135 0.385,0.188 10 false CANL 4.917,2.052 5.625,2.354 0.708,0.302 10 false CANH 4.938,2.49 5.323,2.677 0.385,0.188 10 false CANL 0.865,2.271 2.844,2.469 1.979,0.198 10 false to CAN Communication System 0.531,3.458 2.396,3.656 1.865,0.198 10 false : CAN Communication Line 5.073,1.5 5.708,1.792 0.635,0.292 10 false ECM 4.396,3 6.479,3.427 2.083,0.427 10 false Airbag Sensor Assembly (Yaw Rate and Acceleration Sensor) 2.271,0.354 2.448,0.51 0.177,0.156 10 false 5 2.271,0.802 2.448,0.958 0.177,0.156 10 false 19 4.667,0.354 4.844,0.51 0.177,0.156 10 false 13 4.677,0.792 4.854,0.948 0.177,0.156 10 false 26 4.656,1.906 4.833,2.063 0.177,0.156 10 false 26 4.667,2.344 4.844,2.5 0.177,0.156 10 false 27 5.073,1.344 5.448,1.49 0.375,0.146 10 false A38 4.396,2.844 4.823,3.042 0.427,0.198 10 false F150

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 60 seconds or more.

2.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC U0129 is not output A
DTC U0129 is output B



A

2.READ VALUE USING GTS (G SENSOR)

B

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of yaw rate and acceleration sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of yaw rate and acceleration sensor
·

2.31 V to 2.69 V: Vehicle on level ground

·

1.88 V to 2.5 V: Decelerating

·

2.5 V to 3.11 V: Accelerating

·

Set to 1.87 V: G sensor malfunction

·

Set to 1.87 V: Communication malfunction


-

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

3.REPLACE AIRBAG SENSOR ASSEMBLY

B

3.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Replace the airbag sensor assembly (yaw rate and acceleration sensor).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT