FAIL-SAFE FUNCTION
When communication fails in any of the CAN bus lines (communication lines), a fail-safe function(s) will operate. The fail-safe function that is specified for each system operates to prevent those systems from malfunctioning.
The following table shows the effects on each system when communication is impossible. (For further details, see the pages for each system.)
| Function | Control Master
(Main ECU to determine controls) |
System Related | Fail-safe Operation | Driver Detectable | DTC Detection
(ECU that stored DTC) |
|---|---|---|---|---|---|
| ABS control | Brake actuator assembly | - | Only EBD control is available. | ·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake warning light illuminates. |
U0073
(Brake actuator assembly) |
| VSC control | Brake actuator assembly | ·
ECM ·
Steering sensor ·
Airbag sensor assembly |
·
VSC is disabled. ·
Only EBD control is available. |
·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake warning light illuminates. |
U0073
U0100 U0123 U0126 (Brake actuator assembly) |
| TRC control | Brake actuator assembly | ·
ECM ·
Steering sensor ·
Airbag sensor assembly |
·
TRC is disabled. ·
Only EBD control is available. |
·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake warning light illuminates. |
U0073
U0100 U0123 U0126 (Brake actuator assembly) |
| Hill-start Assist Control
·
Maintains brake torque in order to prevent the vehicle from rolling backwards when stopped on an uphill road. |
Brake actuator assembly | ·
ECM ·
Steering sensor ·
Airbag sensor assembly |
·
Hill-start assist control is disabled. ·
Only EBD control is available. |
·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake warning light illuminates. |
U0073
U0100 U0123 U0126 (Brake actuator assembly) |
| PCS Control
·
Applies the brakes based on information from the radar/camera system in order to avoid a collision. |
Brake actuator assembly | Millimeter wave radar sensor assembly | PCS brake control is disabled. | ·
ABS warning light illuminates. ·
SLIP indicator light illuminates. ·
Brake warning light illuminates. |
U0073
(Brake actuator assembly) |
| ACC Control
·
Applies the brakes based on information from the radar/camera system in order to follow the vehicle in front. |
Brake actuator assembly | ECM | ACC brake control is disabled. | ·
ABS warning light illuminates. ·
SLIP indicator light illuminates. ·
Brake warning light illuminates. |
U0073
(Brake actuator assembly) |
| Brake Hold Control
·
Maintains the brake oil pressure when the vehicle is stopped. |
Brake actuator assembly | ·
ECM ·
Steering sensor ·
Airbag sensor assembly ·
Main body ECU (multiplex network body ECU) |
Brake hold control is disabled. | ·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake hold operated indicator light blinks. ·
Brake warning light illuminates. |
U0073
U0100 U0123 U0126 U0142 (Brake actuator assembly) |
| DAR Control
·
Automatically releases EPB when accelerator pedal is depressed while EPB is still in a locked condition. |
Brake actuator assembly | ·
ECM ·
Steering sensor ·
Airbag sensor assembly |
DAR control is disabled. | ·
ABS warning light illuminates. ·
SLIP indicator illuminates. ·
Brake warning light illuminates. ·
Electric parking brake warning light illuminates. |
U0073
U0100 U0123 U0126 U0142 (Brake actuator assembly) |
| Vehicle Speed Display | Combination meter assembly | Brake actuator assembly | Speedometer is controlled based on a default vehicle speed of 0 km/h (0 mph). | - | U0129
(Combination meter assembly) |
| Tachometer Display | Combination meter assembly | ECM | Needle of tachometer remains at 0 rpm. | - | U0100
(Combination meter assembly) |
| Meter Display
·
Displays vehicle condition and controls indicator lights. |
Combination meter assembly | ·
Power steering ECU assembly ·
Airbag sensor assembly ·
Brake actuator assembly ·
ECM ·
Forward recognition camera ·
Headlight ECU sub-assembly LH |
·
Vehicle information is not displayed. ·
Lights do not illuminate or lights remain illuminated. |
- | U0100
U0129 U0131 U0151 U0182 (Combination meter assembly) |
| Air Conditioning Control
·
Corrects engine speed, such as for idle up. ·
Controls outlet air temperature, outlet mode change and airflow volume based on engine coolant temperature signal. |
Air conditioning amplifier assembly | ECM | ·
If the target frame cannot be received, the previous values are kept. ·
When it is judged that there is a communication interruption, value is set to 80°C (176°F). |
- | U0100
(Air conditioning amplifier assembly) |
| Engine Stop and Start System Control
·
Controls prohibition/startup requests according to engine stop and start system information. |
Air conditioning amplifier assembly | Engine stop and start ECU | If the target frame cannot be received, the previous values are kept. | - | - |
| Compressor Control
·
Judges compressor lock according to engine speed. |
Air conditioning amplifier assembly | ECM | If the target frame cannot be received, the previous values are kept. | - | U0100
(Air conditioning amplifier assembly) |
| Simple Load Control
·
Performs electric load control according to load control level signal. |
Air conditioning amplifier assembly | Power steering ECU assembly | If the target frame cannot be received, the previous values are kept. | - | U0131
(Air conditioning amplifier assembly) |
| Panel Dimming Control
·
Outputs dimming information to the A/C panel according to the display dimming information. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | If the target frame cannot be received, the previous values are kept. | - | U0142
(Air conditioning amplifier assembly) |
| Destination Determination Control
·
Switches the A/C control pattern according to the destination information. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | If the target frame cannot be received, the previous values are kept. | - | U0142
(Air conditioning amplifier assembly) |
| Ambient Temperature Correction Control
·
Switches air conditioning system operation condition and corrects value of displayed ambient temperature according to vehicle speed signal. |
Air conditioning amplifier assembly | Combination meter assembly | ·
If the target frame cannot be received, the previous values are kept. ·
When it is judged that there is a communication interruption, value is set to 0 km/h (0 mph) |
- | U0155
(Air conditioning amplifier assembly) |
| Solar Calibration Control
·
Calibrates air conditioning control using the value from the solar sensor. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | ·
If the target frame cannot be received, the previous values are kept. ·
When it is judged that there is a communication interruption, value is set to 0 W/m2. |
- | U0142
(Air conditioning amplifier assembly) |
| Outside temperature compensation control
·
Based on outside air temperature sensor data values, air conditioning control compensation and outside air temperature display output value compensation are performed. |
Air conditioning amplifier assembly | Main body ECU (multiplex network body ECU) | If the target frame cannot be received, the previous values are kept. | - | U0142
(Air conditioning amplifier assembly) |
| Freeze frame data output function
·
Controlled according to timestamp request specifications. |
Air conditioning amplifier assembly | Central gateway ECU (network gateway ECU) | If the target frame cannot be received, the previous values are kept. | - | - |
| Blind Spot Monitor Control
·
Detects vehicle in blind spot of adjacent lane and informs driver. |
Blind spot monitor sensor LH | ·
Steering sensor ·
Brake actuator assembly ·
Main body ECU (multiplex network body ECU) ·
ECM |
- | Displays messages on the multi-information display. | U0100
U0126 U0129 U0142 (Blind spot monitor sensor LH) |
| LDA System
·
Sounds an alarm when deviating from the lane, and performs steering assist toward the center of the lane. |
Forward recognition camera | ·
ECM ·
Steering sensor ·
Brake actuator assembly ·
Power steering ECU assembly ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Millimeter wave radar sensor assembly |
Control stops. | ·
Displays messages on the multi-information display. ·
Buzzer sounds. |
U0100
U0123 U0126 U0129 U0131 U0142 U0155 U0235 U023A (Forward recognition camera) |
| Automatic High Beam Function
·
High Beam Light Distribution Control |
Forward recognition camera | ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Steering sensor ·
Brake actuator assembly |
The current state is maintained. | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
B124B
(Main body ECU (multiplex network body ECU)) |
| Road Sign Assist Function
·
Road Sign Assist |
Forward recognition camera | ·
Brake actuator assembly ·
Airbag sensor assembly |
Road sign assist function is canceled. | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0123
U0129 (Forward recognition camera) |
| Dynamic Radar Cruise Control System
·
Accelerates or decelerates the vehicle to maintain the distance to the vehicle ahead. |
Millimeter wave radar sensor assembly | ·
Brake actuator assembly ·
Airbag sensor assembly ·
ECM |
Control stops. | Displays messages on the multi-information display. | U0100
U0125 U0126 U0129 (Millimeter wave radar sensor assembly) |
| Pre-collision System
·
Controls the brakes immediately before a crash. |
Millimeter wave radar sensor assembly | ·
ECM ·
Forward recognition camera ·
Brake actuator assembly ·
Steering sensor ·
Airbag sensor assembly |
Control stops. | ·
Displays messages on the multi-information display. ·
Buzzer Sounds. |
U0100
U0125 U0126 U0129 U0235 U023A U1002 (Millimeter wave radar sensor assembly) |
| Entry Function
·
Entry lock/unlock and back door unlatch ·
Warning ·
Performs entry illumination (Interior illumination, etc.). ·
Displays messages to inform the driver that it is possible to start the SFI system. |
·
Main body ECU (multiplex network body ECU) ·
Certification ECU (smart key ECU assembly) |
·
ECM ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly |
·
Entry lock/ unlock or back door unlatch does not operate. ·
Warning functions (Key confinement, Key not in vehicle, Key reminder etc.) do not operate, Key confinement prevention control does not operate. ·
Entry illumination does not operate. |
- | U0100
U0142 U0155 (Certification ECU (smart key ECU assembly)) |
| Wireless Function
·
Operates the wireless lock/unlock functions, etc. |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Wireless lock/unlock function do not operate. | - | U0142
(Certification ECU (smart key ECU assembly)) |
| Engine Switch Backlighting Control
·
Turns on/off engine switch illumination linked with interior lights etc. |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | ·
When the engine switch backlight is not illuminated: Does not illuminate. ·
When the engine switch backlight is illuminated as the DOME light illuminates: Does not turn off. |
- | U0142
(Certification ECU (smart key ECU assembly)) |
| Security Indicator Display Function
·
Displays the immobiliser security condition. |
Certification ECU (smart key ECU assembly) | Main body ECU (multiplex network body ECU) | Security condition cannot display normally (illuminates during security warning preparation/security warning). | - | U0142
(Certification ECU (smart key ECU assembly)) |
| Air Conditioning Control
·
Controls air conditioning functions such as set temperature adjustment, air outlet selection, etc. by operating display audio controller or Remote Touch. |
Radio and display receiver assembly | Air conditioning amplifier assembly | ·
Air conditioning system indicators turn off. ·
If set temperature is shown on multi-information display or multi-display, set temperature display turns off. |
Displays messages on the multi-information display. | U0073
U0164 (Radio and display receiver assembly) |
| Fuel Consumption Display
·
Displays graph of fuel consumption per minute and history of total fuel consumption. |
Radio and display receiver assembly | ·
ECM ·
Brake actuator assembly ·
Combination meter assembly |
When communication with ECM or brake actuator assembly is interrupted:
·
Display is not updated. When communication with combination meter assembly is interrupted: ·
Depending on the interrupted signal, the instantaneous fuel economy, average speed, elapsed time (after start) or drivable mileage is not displayed. ·
Numeric part of driveable mileage is cleared. |
- | U0100
U0129 U0155 (Radio and display receiver assembly) |
| Destination Identification
·
Identifies destination based on destination and destination package information, and selects the time zone and language used for the display. |
Radio and display receiver assembly | Main body ECU (multiplex network body ECU) | Determines the destination according to the last received value and operates accordingly (if there is no last received value, the system operates using the default value). | Time zone and language selection screen are different from actual destination. | U0140
(Radio and display receiver assembly) |
| Vehicle Customize Function
·
Changes the behavior and control parameters of various functions (illumination lighting time, etc.) according to the user operation via the screen. |
Radio and display receiver assembly | ·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly ·
Certification ECU (smart key ECU assembly) |
·
When a remote communication usage application is performed (customize or remote diagnosis), the information is processed regardless of whether the main body ECU (multiplex network body ECU) has permitted or prohibited remote communication. ·
3 retries are performed (including the first time). |
The customize options for items related to the ACN, BDB and IDT are not displayed or the settings cannot be saved. | ·
U0073 ·
B15F5 ·
B15F6 ·
B15F7 (Radio and display receiver assembly) |
| Meter-linked Function
·
Changes display based on customization information set through the meter. Outputs the customization information set in the system. |
Radio and display receiver assembly | Combination meter assembly | Maintains the last valid state. | - | - |
| Information Sound Adjustment Function
·
Receives flags from the driving support ECU to operate the alarm, and limits or mutes multimedia audio while the alarm is in operation. |
Radio and display receiver assembly | ·
Forward recognition camera ·
Clearance warning ECU assembly |
Audio mute is canceled. | - | - |
| Rear View Monitor System
·
Displays images from the rear view camera. |
Radio and display receiver assembly | ECM | Screen does not change to the camera screen. | - | U0100
(Radio and display receiver assembly) |
| Destination Determination Function
·
Judges the destination and uses the information for an operation condition for the app. ·
Judges the handle position and uses the information for an operation condition for the app. |
Clearance warning ECU assembly | Main body ECU (Multiplex network body ECU) | It operates according to previous EEPROM values when a communication stop occurs. | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U014087
(Clearance warning ECU assembly) |
| Shift Position Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | ECM | Changes to an operation state which is used when the shift lever is in P. | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U010087
(Clearance warning ECU assembly) |
| Engine Model Information
·
Judges the engine/transmission model and switches the control constant table. ·
Is used as an operation condition for the app. ·
Determines whether the vehicle is 2WD or AWD and switches the steering parameter table. |
Clearance warning ECU assembly | ECM | It operates according to previous EEPROM values when a communication stop occurs. | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U010087
(Clearance warning ECU assembly) |
| Engine Control State Information
·
Judges whether the engine is on or off. ·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | ECM | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U010087
(Clearance warning ECU assembly) |
| During CSR Request Operation G
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | ECM | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U010087
(Clearance warning ECU assembly) |
| Cruise Control Information
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | ECM | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U010087
(Clearance warning ECU assembly) |
| Accelerator Opening Angle
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | ECM | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U010087
(Clearance warning ECU assembly) |
| Power Steering Control Information
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Power steering ECU assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U013187
(Clearance warning ECU assembly) |
| Turn Light Condition
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Combination meter assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U015587
(Clearance warning ECU assembly) |
| Clearance Sonar Main Switch Information
·
Is used as an operation condition for the clearance warning ECU assembly. |
Clearance warning ECU assembly | Combination meter assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U015587
(Clearance warning ECU assembly) |
| Clearance Sonar Buzzer Mute/Volume Change
·
Is used as an operation condition for the clearance warning ECU assembly. |
Clearance warning ECU assembly | Combination meter assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U015587
(Clearance warning ECU assembly) |
| Data Continuity (Valid/Invalid) Flag
+B Open Circuit Malfunction Sensor Malfunction Steering Angle Signal Sensor Internal Zero Point Memorization Invalid/Valid Steering Angle Sensor Internally Memorized Zero Point Value Steering sensor Calculated Value ·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Steering sensor | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012687
(Clearance warning ECU assembly) |
| Wheel Speed Information
·
The wheel speed signal from each wheel (after 1/2 filter) is used to calculate the vehicle speed. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Wheel Speed Sensor State Information, Wheel Speed Calculated Value
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | (Clearance warning ECU assembly)
U012987 |
| Master Cylinder Pressure Malfunction Flag
Master Cylinder Pressure Invalid Flag Master Cylinder Pressure BA Fail Signal STP Switch Signal STP Switch Open Circuit Signal During VSC Control During ABS Control ·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| TRC Operating Flag
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Brake Control State Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Yaw Rate Sensor State Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Speed Information Signal for Each Wheel
·
Calculates the amount of movement. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| VSC OFF, TRC OFF Indicator
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Brake actuator assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012987
(Clearance warning ECU assembly) |
| Yaw Rate Sensor State Signal
·
Is used as an operation condition for the app. |
Clearance warning ECU assembly | Airbag sensor assembly | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | App stops operating (displays a warning message in the combination meter and sounds the buzzer). | U012587
(Clearance warning ECU assembly) |
| Power Steering Control
·
Calculates assist current according to torque sensor value and vehicle speed and drives motor. |
Power steering ECU assembly | ·
ECM ·
Brake actuator assembly ·
Airbag sensor assembly ·
Steering sensor |
·
Control is performed temporarily with the steering assist amount set to that used when the vehicle speed is 100 km/h (62 mph). ·
Zero point learning is not performed. ·
Drivability degrades (compensation control using steering angle is stopped). |
EPS warning light illuminates. | U0100
U0129 (Power steering ECU assembly) |
| Assist Map Selection
·
Selects proper assist map according to destination, engine type, etc. |
Power steering ECU assembly | ECM | Default map is used to assist because proper assist map cannot be selected. (Steering feel may be different.) | EPS warning light illuminates. | C1581
(Power steering ECU assembly) |
| VDIMα System
·
Calculates current to be used for steering assist according to commanded value from VSC, and then operates motor. |
Power steering ECU assembly | Brake actuator assembly | VDIMα control is stopped. | - | U0129
(Power steering ECU assembly) |
| Engine/Hybrid Toggle
·
So that the same parts can be used for conventional and hybrid vehicles, this toggles the communication type. |
Power steering ECU assembly | ECM | Control is performed temporarily with the steering assist amount set to that used when the vehicle speed is 100 km/h (62 mph). | EPS warning light illuminates. | U0100
(Power steering ECU assembly) |
| Engine System Indicator Display
·
Estimates whether injectors are clogged and requests that a message be displayed informing user that injectors need maintenance. ·
Estimates whether oil has deteriorated and requests that a message be displayed informing user that oil needs to be replaced. |
ECM | Combination meter assembly | ·
System is unable to inform user that oil needs to be replaced or injectors need maintenance. ·
Combination meter display cannot be cleared. |
- | - |
| Electric Load Control
·
Performs idle up according to electric load. |
ECM | ·
Air conditioning amplifier assembly ·
Power steering ECU assembly ·
Main body ECU (multiplex network body ECU) |
Idle up according to electric load is not performed. | Not possible. (Idle speed changes.) | - |
| Air Conditioning Cooperative Operation
·
Performs idle up according to compressor load. ·
Performs air conditioning cut control. |
ECM | Air conditioning amplifier assembly | Air conditioning system does not use cooperative controls. (Idle up is not performed.) | Air conditioning system does not operate. | - |
| Charge Control
·
Performs idle up according to charging request. |
ECM | ·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) |
Idle up according to charging request is not performed. | Taillights flicker and blower airflow changes. | - |
| Sprung mass damping control
·
Uses transitional driving force control is to improve behavior (pitch, bounce) of sprung vehicle mass when disturbed. |
ECM | ·
Brake actuator assembly ·
4WD ECU assembly |
Sprung vehicle mass damping control does not operate. Does not use transitional driving force control to improve behavior (pitch, bounce) of sprung vehicle mass when disturbed. | - | - |
| Eco Driving Indicator
·
Displays information to the driver to encourage Eco-driving. |
ECM | - | - | No information is displayed. | - |
| Integrated Control (VDM)
·
Estimates the driver requested torque based on the accelerator pedal operation and performs torque characteristic control according to driving conditions so that driveability, acceleration performance and acceleration feeling are improved. |
ECM | ·
Millimeter wave radar sensor assembly ·
Brake actuator assembly ·
Airbag sensor assembly ·
Steering sensor |
Does not estimate the driver requested torque based on the accelerator pedal operation and does not perform torque characteristic control according to driving conditions and as a result, driveability, acceleration performance and acceleration feeling are not improved. | - | - |
| Eco Control
·
Adjusts throttle response in consideration of actual fuel economy. |
ECM | ·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) |
Eco mode does not operate. | - | - |
| ECT System Indicator Display
·
Meter display (Displays shift position, states of switches, system modes, etc.) |
ECM | Combination meter assembly | Indicator light does not illuminate. | - | - |
| Neutral Control
·
Reduces engine load and performs idle up. |
ECM | ·
Brake actuator assembly ·
Airbag sensor assembly |
Neutral control is not performed. | - | U0129
U012987 (ECM) |
| Coast Downshift Timing Change According to Air Conditioning Load
·
Delays upshifts according to warm-up request. |
ECM | Air conditioning amplifier assembly | Coast downshift does not occur. | Coast downshift shock reduction performance deteriorates. | - |
| Cruise Control
·
Controls vehicle speed by adjusting throttle valve angle automatically. |
ECM | ·
Millimeter wave radar sensor assembly ·
Brake actuator assembly ·
Combination meter assembly |
Cruise control does not operate. | Displays messages on the multi-information display. | - |
| Headlight Leveling Control (Headlight Control)
·
Adjusts headlights vertical aiming according to wheel speed and vehicle pitch angle determined using vehicle height sensor. |
Headlight ECU sub-assembly LH | ·
Brake actuator assembly ·
Main body ECU (multiplex network body ECU) |
Control stops. | - | U0129
U0142 (Headlight ECU sub-assembly LH) |
| Headlight Leveling Indicator
·
Monitors leveling system malfunctions and when a malfunction is detected, sends an indicator illumination request to the combination meter assembly. |
Headlight ECU sub-assembly LH | Combination meter assembly | Maintains the leveling indicator state. | - | U0155
(Headlight ECU sub-assembly LH) |
| Destination Identification
·
Checks if the destination information stored in the headlight ECU sub-assembly LH and the destination information data transmitted in the CAN bus lines are the same. |
Headlight ECU sub-assembly LH | ·
ECM ·
Main body ECU (multiplex network body ECU) |
- | - | U0100
U0142 (Headlight ECU sub-assembly LH) |
| Low Beam Headlights, High Beam Headlights, Clearance Lights and Side Marker Lights
·
Turns the specified light source on and off according to low beam, high beam command data. |
Main body ECU (multiplex network body ECU) | Headlight ECU sub-assembly LH | The low beam headlights, clearance lights and side marker lights are forcibly illuminated. | - | U0142
(Headlight ECU sub-assembly LH) |
| LED Headlight Indicator
·
Monitors low beam LED malfunctions and when a malfunction is detected, sends an indicator illumination request to the meter. |
Headlight ECU sub-assembly LH | Combination meter assembly | Maintains the LED headlight indicator status. | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0073
U1000 (Headlight ECU sub-assembly LH) |
| Headlight Cleaner Signal Output
·
Outputs the headlight cleaner relay ON signal based on the direct line front washer switch signals, headlight cleaner switch signals, low beam illumination command from the main body ECU (multiplex network body ECU) and IG data. |
Headlight ECU sub-assembly LH | Combination meter assembly | Stops headlight cleaner operation. | - | U0142
(Headlight ECU sub-assembly LH) |
| Door Lock
·
Controls key linked and automatic door lock/unlock function, key confinement prevention function, etc. |
Main body ECU (multiplex network body ECU) | Airbag sensor assembly | Key linked door lock/unlock function is performed even when the ignition switch is ON and the driver seatbelt is fastened. | - | U0151
(Main body ECU (multiplex network body ECU)) |
| Alarm
·
Sounds various warnings. |
Main body ECU (multiplex network body ECU) | ·
ECM ·
Certification ECU (smart key ECU assembly) |
- | - | U0100
U0120 (Main body ECU (multiplex network body ECU)) |
| Automatic Dimming of Display
·
Controls display dimming control. |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Automatically performs display dimming control when tail mode is not canceled (when the light sensor illuminance signal value is less than the display dimming value, the interior displays and indicators are dimmed). | - | U0155
(Main body ECU (multiplex network body ECU)) |
| Illumination
·
Performs illumination control. |
Main body ECU (multiplex network body ECU) | ·
Certification ECU (smart key ECU assembly) ·
ECM |
·
The dome light turns off. ·
The outside handle illumination turns off. ·
The foot light is adjusted. |
The dome light does not turn off immediately after exiting the vehicle. | U0101
U0327 (Main body ECU (multiplex network body ECU)) |
| Diagnostic/C-BEST
·
Diagnostic phase 4 communication. |
- | All ECUs connected to CAN | Exits diagnostic mode. | - | - |
| Entry and Start Function/Wireless
·
Controls entry and start function/wireless functions. |
Certification ECU (smart key ECU assembly) | Certification ECU (smart key ECU assembly) | Entry lock/unlock control not possible. | - | U0327
(Main body ECU (multiplex network body ECU)) |
| Lighting Control
·
Controls the daytime running lights. |
Main body ECU (multiplex network body ECU) | ECM | Daytime running light control is not performed. | - | U0100
(Main body ECU (multiplex network body ECU)) |
| TPMS
·
Monitors the tire pressure and meter speed, etc. and operates the meter indicators and multi-information display. |
Main body ECU (multiplex network body ECU) | Combination meter assembly | Sends an initial communication value to the BERKES. | The tire pressure monitor sensor indicator in the combination meter assembly blinks for 1 minute and then stays illuminated. | U0155
(Main body ECU (multiplex network body ECU)) |
| Automatic High Beam
·
Detects oncoming traffic, vehicles ahead, street lights, etc. using an onboard sensor and automatically turns the high beam lights on and off. |
Main body ECU (multiplex network body ECU) | ·
Headlight ECU sub-assembly LH ·
Forward recognition camera |
The system does not operate. | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0182
U023A (Main body ECU (multiplex network body ECU)) |
| Lighting Control
·
The headlight ECU controls the loading around the headlights (body ECU sends an illumination request to headlight ECU) |
Headlight ECU sub-assembly LH | Main body ECU (multiplex network body ECU) | - | ·
Buzzer sounds. ·
Displays messages on the multi-information display. |
U0182
(Main body ECU (multiplex network body ECU)) |
| Lighting Control
·
European headlight auto-cut |
Main body ECU (multiplex network body ECU) | Brake booster with master cylinder assembly | Maintains previous values. | - | U0129
(Main body ECU (multiplex network body ECU)) |
| ATC-4WD System
·
Controls drive force of the front and rear wheels in accordance with the driving conditions. |
4WD ECU assembly | ·
ECM ·
Steering sensor ·
Brake actuator assembly ·
Airbag sensor assembly ·
Main body ECU (multiplex network body ECU) ·
Air conditioning amplifier assembly |
Depending on the malfunctioning communication line, any of the following controls are performed.
·
Control is prohibited. ·
Control is maintained using the latest value received from the airbag sensor assembly. ·
Control is maintained using the latest value received from the brake actuator assembly. ·
Control is maintained using the latest value received from the ECU or sensor. |
4WD warning light illuminates. | U0073
U0100 U0126 U0129 (4WD ECU assembly) |
| ERA-GLONASS
·
Makes an emergency call to the center and notifies an operator of the vehicle location when deployment of an airbag is detected or the manual (SOS) switch is pressed. |
Telematics transceiver | ECM | When communication with the ECM is lost or there is a communication error, the manual (SOS) switch indicator (red) illuminates. | - | U0100
(Telematics transceiver) |
| Panoramic View Monitor
·
Shows an overhead map along with front, side and rear images on the display. ·
Shows guide lines on the displayed image in tandem with the steering angle. ·
Displays the clearance sonar detection area. ·
Displays the RCTA detection conditions. |
Parking assist ECU | ·
Steering sensor ·
Brake actuator assembly ·
ECM ·
Main body ECU (multiplex network body ECU) ·
Clearance warning ECU assembly ·
Blind spot monitor sensor LH ·
Radio and Display Receiver Assembly |
·
An alert mark is displayed. ·
The guide lines (linked lines) are not displayed. ·
Distance guide line 3 (the fixed guide line) is displayed in red. ·
The guide lines (fixed lines) are not displayed. ·
The clearance sonar icon is not displayed. ·
The RCTA icon is not displayed. ·
Soft switch is grayed out. ·
Language switching works with stored values. ·
It operates according to previous values of vehicle information. ·
The camera screen display is stopped (however, the displaying of images that comply with regulations continues). ·
Nothing is displayed, except for images that comply with regulations. ·
The screen display is stopped when the front mode screen is displayed. ·
It operates as if the mirrors are open. ·
Screen design operates according to previous values. |
·
An alert mark is displayed on the top of the camera screen. ·
The clearance sonar icon is not displayed. ·
The RCTA icon is not displayed. |
U0073
U0100 U0126 U0129 U0140 U0163 U0233 U1110 (Parking assist ECU) |