Home › Vehicle Exterior › LIGHTING (EXT) › REAR COMBINATION LIGHT ASSEMBLY(for LED Type) › from 2019.09
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0295720 REAR COMBINATION LIGHT ASSEMBLY(for LED Type) G

LIGHTING (EXT)  REAR COMBINATION LIGHT ASSEMBLY(for LED Type)  INSPECTION  


PROCEDURE

Hide 81560 1.INSPECT REAR COMBINATION LIGHT ASSEMBLY LH

a.
E420088C03
1.698,0.844 1.26,0.458 true 2.573,0.813 2.052,0.938 true 2.615,1.406 2.052,1.24 true 1.365,0.927 0.917,0.833 true 1.646,1.271 1.198,1.667 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.073,0.354 1.385,0.51 0.313,0.156 10 false TL 0.948,1.677 1.344,1.875 0.396,0.198 10 false TRN 2.677,0.729 2.99,0.885 0.313,0.156 10 false B 2.688,1.365 3,1.521 0.313,0.156 10 false E 0.604,0.729 1,0.927 0.396,0.198 10 false TRN
*a Component without Harness Connected
(Rear Combination Light Assembly LH)


Check that the rear combination light assembly LH.

i.

Apply battery voltage to the rear combination light assembly LH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (B)
Battery negative (-) → Terminal 4 (E)
Stop light comes on


If the result is not as specified, replace the rear combination light assembly LH.


ii.

Apply battery voltage to the rear combination light assembly LH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 2 (TL)
Battery negative (-) → Terminal 4 (E)
Taillight comes on


If the result is not as specified, replace the rear combination light assembly LH.


iii.

Apply battery voltage to the rear combination light assembly LH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 5 (TRN), Terminal 3 (TRN)
Battery negative (-) → Terminal 4 (E)
Turn signal light comes on


NOTICE:

The turn signal light will not have sequential effect when checking by this method.


If the result is not as specified, replace the rear combination light assembly LH.



Hide 81550 2.INSPECT REAR COMBINATION LIGHT ASSEMBLY RH

a.
E420088C03
1.698,0.844 1.26,0.458 true 2.573,0.813 2.052,0.938 true 2.615,1.406 2.052,1.24 true 1.365,0.927 0.917,0.833 true 1.646,1.271 1.198,1.667 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.073,0.354 1.385,0.51 0.313,0.156 10 false TL 0.948,1.677 1.344,1.875 0.396,0.198 10 false TRN 2.677,0.729 2.99,0.885 0.313,0.156 10 false B 2.688,1.365 3,1.521 0.313,0.156 10 false E 0.604,0.729 1,0.927 0.396,0.198 10 false TRN
*a Component without Harness Connected
(Rear Combination Light Assembly RH)


Check that the rear combination light assembly RH.

i.

Apply battery voltage to the rear combination light assembly RH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (B)
Battery negative (-) → Terminal 4 (E)
Stop light comes on


If the result is not as specified, replace the rear combination light assembly RH.


ii.

Apply battery voltage to the rear combination light assembly RH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 2 (TL)
Battery negative (-) → Terminal 4 (E)
Taillight comes on


If the result is not as specified, replace the rear combination light assembly RH.


iii.

Apply battery voltage to the rear combination light assembly RH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 5 (TRN), Terminal 3 (TRN)
Battery negative (-) → Terminal 4 (E)
Turn signal light comes on


NOTICE:

The turn signal light will not have sequential effect when checking by this method.


If the result is not as specified, replace the rear combination light assembly RH.