Home › Vehicle Exterior › LIGHTING (EXT) › REAR LIGHT ASSEMBLY (for LED Type) › from 2019.09
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0295723 REAR LIGHT ASSEMBLY(for LED Type) G

LIGHTING (EXT)  REAR LIGHT ASSEMBLY(for LED Type)  INSPECTION  


PROCEDURE

Hide 81590A 1.INSPECT REAR LIGHT ASSEMBLY LH

a.
E420094C02
1.521,0.938 1.052,0.76 true 2.333,0.823 1.833,0.958 true 1.854,1.156 2.406,1.26 true 1.531,1.354 1.031,1.49 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.896,0.646 1.458,0.823 0.563,0.177 10 false E 2.365,0.729 2.677,0.885 0.313,0.156 10 false TRN 2.448,1.208 2.76,1.406 0.313,0.198 10 false TL 0.74,1.479 1.052,1.635 0.313,0.156 10 false TRN
*a Component without Harness Connected
(Rear Light Assembly LH)


Check that the rear light assembly LH.

i.

Apply battery voltage to the rear light assembly LH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (TRN), Terminal 6 (TRN)
Battery negative (-) → Terminal 2 (E)
Turn signal light comes on


NOTICE:

The turn signal light will not have sequential effect when checking by this method.


If the result is not as specified, replace the rear light assembly LH.


ii.

Apply battery voltage to the rear light assembly LH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 3 (TL)
Battery negative (-) → Terminal 2 (E)
Taillight comes on


If the result is not as specified, replace the rear light assembly LH.



Hide 81580D 2.INSPECT REAR LIGHT ASSEMBLY RH

a.
E420094C02
1.521,0.938 1.052,0.76 true 2.333,0.823 1.833,0.958 true 1.854,1.156 2.406,1.26 true 1.531,1.354 1.031,1.49 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 0.896,0.646 1.458,0.823 0.563,0.177 10 false E 2.365,0.729 2.677,0.885 0.313,0.156 10 false TRN 2.448,1.208 2.76,1.406 0.313,0.198 10 false TL 0.74,1.479 1.052,1.635 0.313,0.156 10 false TRN
*a Component without Harness Connected
(Rear Light Assembly RH)


Check that the rear light assembly RH.

i.

Apply battery voltage to the rear light assembly RH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 1 (TRN), Terminal 6 (TRN)
Battery negative (-) → Terminal 2 (E)
Turn signal light comes on


NOTICE:

The turn signal light will not have sequential effect when checking by this method.


If the result is not as specified, replace the rear light assembly RH.


ii.

Apply battery voltage to the rear light assembly RH and check that the light comes on.

OK:
Condition Specified Condition
Battery positive (+) → Terminal 3 (TL)
Battery negative (-) → Terminal 2 (E)
Taillight comes on


If the result is not as specified, replace the rear light assembly RH.