Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door) › 2019.09–2020.08
RM32H0E _59 Vehicle Exterior _060783 EXTERIOR PANELS / TRIM _0298078 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision System
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
·

Door glass

·

Door glass run


Initialize Power Window Control System
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284C 3.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

Hide 74232 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Hide 74231 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Hide 67602 6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67492A 7.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 67862 8.DISCONNECT FRONT DOOR WEATHERSTRIP

Hide 68195 9.REMOVE FRONT DOOR BELT SEAL

Hide 68172A 10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 67838A 11.REMOVE FRONT DOOR VENT SEAL

Hide 87940 12.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

Hide 67832 13.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68102 14.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 67664 15.REMOVE DOOR FRAME UPPER GARNISH

Hide 68151C 16.REMOVE FRONT DOOR GLASS RUN

Hide 67402F 17.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Hide 68126 18.REMOVE FRONT DOOR FIX WINDOW GLASS

Hide 75966B 19.REMOVE NO. 4 FRONT DOOR STRIPE

HINT:

When removing the No. 4 front door stripe, heat the vehicle body and No. 4 front door stripe using a heat light.


Heating Temperature
Item Temperature
No. 4 Front Door Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Using a heat light, heat the No. 4 front door stripe and vehicle body.


b.
B458783

Pull back on one of the ends of the No. 4 front door stripe to remove it.

HINT:

When pulling on the No. 4 front door stripe, pull it parallel to the vehicle body.



Hide 75986G 20.REMOVE FRONT DOOR OUTSIDE STRIPE

HINT:

When removing the front door outside stripe, heat the vehicle body and front door outside stripe using a heat light.


Heating Temperature
Item Temperature
Front Door Outside Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Using a heat light, heat the front door outside stripe and vehicle body.


b.
B458784

Pull back on one of the ends of the front door outside stripe to remove it.

HINT:

When pulling on the front door outside stripe, pull it parallel to the vehicle body.



Hide 75976G 21.REMOVE NO. 2 FRONT DOOR STRIPE

HINT:

When removing the No. 2 front door stripe, heat the vehicle body and No. 2 front door stripe using a heat light.


Heating Temperature
Item Temperature
No. 2 Front Door Stripe and Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the vehicle body excessively.


a.

Using a heat light, heat the No. 2 front door stripe and vehicle body.


b.
B458785

Pull back on one of the ends of the No. 2 front door stripe to remove it.

HINT:

When pulling on the No. 2 front door stripe, pull it parallel to the vehicle body.