Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.09
RM32H0E _53 Suspension _059606 TIRE PRESSURE MONITORING _0292310 TIRE PRESSURE WARNING SYSTEM U

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TERMINALS OF ECU  


CHECK TIRE PRESSURE WARNING ECU AND RECEIVER


a.
C368906C01
0.25,1 0.75,1.25 0.5,0.25 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.375,1.042 0.771,1.24 0.396,0.198 10 false M23
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the M23 tire pressure warning ECU and receiver connector and measure the voltage or resistance on the wire harness side.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M23-1 (IG) - M23-12 (GND) SB - W-B IG power source Ignition switch to ON 10 to 16 V
M23-7 (+B) - M23-12 (GND) B*1 - W-B
R*2 - W-B
Power supply (from battery) Always 10 to 16 V
M23-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

*1: w/ Entry and Start System

*2: w/o Entry and Start System



b.

Connect the M23 tire pressure warning ECU and receiver connector.


c.

Measure the voltage and resistance according to the value(s) in the table below. If the result is not as specified, the ECU may be malfunctioning.

HINT:

Measure the values on the wire harness side while the connector is connected.


E129452C52
2,0.75 2.5,1 0.5,0.25 0.115,0.094 0.438,0.344 0.323,0.25 10 false *a 2.125,0.792 2.51,0.969 0.385,0.177 10 false M23
*a Component with harness connected
(Tire Pressure Warning ECU and Receiver)
- -


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M23-3 (CLSW) - M23-12 (GND) Y - W-B Tire pressure warning reset switch
·

Ignition switch to ON

·

Steering pad switch assembly operated, "TPMS" selected on the multi-information display and "ENTER" switch (steering pad switch assembly) pressed and held


Below 1.5 V
·

Ignition switch to ON

·

"ENTER" switch (steering pad switch assembly) off


8 to 15 V
M23-4 (RDA) - M23-12 (GND) G - W-B Output signals Ignition switch to ON Pulse generation (see waveform 1)
M23-5 (PRG) - M23-12 (GND) W - W-B Input signals Ignition switch to ON Pulse generation (see waveform 1)


d.
C240058C03
2.875,1.229 3.115,1.438 0.24,0.208 10 false *b 0.115,0.104 0.323,0.323 0.208,0.219 10 false *a
*a Example
*b GND


Using an oscilloscope, check waveform 1.

Waveform 1:
Item Contents
Terminal M23-4 (RDA) - M23-12 (GND)
M23-5 (PRG) - M23-12 (GND)
Tool setting 5 V/DIV, 5 ms./DIV.
Vehicle condition Ignition switch to ON

HINT:

The waveform shown in the illustration is an example. If the tester displays a waveform that alternates between high and low, where high is a voltage that is between the IG power source voltage and a voltage 2.2 V lower than the IG power source voltage, and where low is a voltage of between 0 and 1.2 V, the ECU can be judged normal.