Home › General › MAINTENANCE › FRONT DISC BRAKE PAD (for TMMT Made) › from 2019.09
RM32H0E _V1 General _059503 MAINTENANCE _0407342 FRONT DISC BRAKE PAD(for TMMT Made) A

MAINTENANCE  FRONT DISC BRAKE PAD(for TMMT Made)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

Immediately after installing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 04945 1.INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn front disc brake pads, the front disc brake anti-squeal shims and front brake pad radial springs must be replaced together with the front disc brake pads.

·

Install the front disc brake anti-squeal shims in the correct position and direction.



a.
C365992C01
2.104,0.719 2.104,0.469 2.104,0.469 3.021,0.469 false 2.74,0.469 2.74,1.115 false 0.469,1.333 0.469,1.667 false 2.323,3.115 2.323,3.25 2.323,3.25 1.083,3.25 false 1.667,2.708 1.667,3.25 false 2.688,2.625 2.688,2.958 false 0.396,1.698 0.708,1.854 0.313,0.156 10 false *1 3.073,0.385 3.385,0.542 0.313,0.156 10 false *2 2.615,3.042 2.927,3.198 0.313,0.156 10 false *1 0.875,3.135 1.188,3.292 0.313,0.156 10 false *2
*1 Front Disc Brake Anti-squeal Shim
*2 Front Brake Pad Radial Springs


Install the front disc brake anti-squeal shim to each front disc brake pad.


b.

Install the 2 front brake pad radial springs to each front disc brake pad.


Hide 2.INSTALL FRONT DISC BRAKE PAD

CAUTION:
·
C368018

After lifting up the front disc brake cylinder assembly, secure it in place before performing any work on it.

·

The front disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.

Push in the front disc brake piston.

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the front disc brake piston.




b.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:

Keep the friction surfaces of the front disc brake pads and front disc free from oil and grease.



c.
C369228C01
1.969,2.75 2.281,2.906 0.313,0.156 10 false *a 1.094,2.677 1.406,2.833 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the front disc brake cylinder slide pin (lower side) and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with a new bolt.

Torque:
31.5 N*m (321 kgf*cm, 23 ft.*lbf)

CAUTION:
·
C368073

When replacing the front disc brake pad, be sure to replace the bolts with new ones.

·

If the bolts are reused, the front disc brake cylinder assembly could come off, which could cause an accident.




Hide 3.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 4.INSTALL FRONT WHEEL