Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › 2019.09–2020.08
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0407373 LIGHTING SYSTEM(w/ Headlight ECU) D

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  SYSTEM DESCRIPTION  


AUTOMATIC LIGHT CONTROL SYSTEM


a.

When the light control switch is in the AUTO position, the automatic light control system detects ambient light levels and controls the low beam headlights, clearance lights, taillights and license plate lights.



LIGHT AUTO TURN-OFF SYSTEM (except Driver Door-linked Light Auto Turn-off System)


a.

The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (headlights, front fog lights, rear fog light*1, taillights, clearance lights and license plate lights).


b.

The lights that will turn off will vary according to the position of the light control switch as shown in the table below.

Switch Condition Outline
Light control switch in AUTO position While the exterior lights are turned on, this control automatically turns them off when the ignition switch is turned from ON to off.
Light control switch in tail or head position While the exterior lights are turned on, this control automatically turns off only the low beam headlights, high beam headlights and the front fog lights*1 when the ignition switch is turned from ON to off.
HINT:

Taillights, clearance lights, license plate lights and rear fog light*2 remain on.



*1: w/ Rear Fog Light




LIGHT AUTO TURN-OFF SYSTEM (for Driver Door-linked Auto Light Turn-off System)


a.

The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (headlights, front fog lights, rear fog light*1, taillights, clearance lights and license plate lights).


b.

When all of the following conditions are met, the headlights, front fog lights*1, rear fog light*2, taillights, clearance lights and license plate lights turn off:

·

The ignition switch is turned from ON to off.

·

The headlights, front fog lights, rear fog light*1, taillights, clearance lights and license plate lights are on.

·

The driver door is opened.


*1: w/ Rear Fog Light




LIGHT AUTO TURN-OFF SYSTEM (w/ Delay Function)


a.

The light auto turn-off system is used to prevent the exterior lights from being accidentally left on (headlights, front fog lights, taillights, clearance lights, license plate lights).

·

This system has the following functions.


Function Outline
Delay Function The exterior lights automatically turn off after 30 seconds when all of the following conditions are met:
·

The ignition switch is turned from ON to off.

·

The low beam headlights are on.

·

All doors are closed after any of the doors are opened.


Door Control Transmitter-linked Function The exterior lights turn off immediately when the delay function is active and the following condition is met:
·

The lock button on the key is pushed after all doors are locked.


Door Open-linked The exterior lights automatically turn off immediately when all of the following conditions are met:
·

The ignition switch is turned from ON to off.

·

The taillights are on. (The low beam headlights are off.)

·

The driver door is opened.





DAYTIME RUNNING LIGHT SYSTEM


a.

The daytime running light system is designed to automatically illuminate the daytime running lights during the daytime to make the vehicle more visible to other vehicles.

·

This system is controlled by the main body ECU (multiplex network body ECU).

·

This system is enabled when the following conditions are met:

-

The ignition switch to ON.

-

The engine speed signal is input (engine running).

-

The light control switch is in the off* or AUTO position (and the taillight are not turned on via the automatic light control system).

*: w/ Light Control Switch Off Position

-

The parking brake switch is off.





DOOR MIRROR FOOT LIGHT CONTROL (w/ Door Mirror Foot Light)


a.

General

·

The door mirror foot light control consists primarily of the fade-in/fade-out function and timer illumination function.

·

This control is performed by the main body ECU (multiplex network body ECU). According to various information, the main body ECU (multiplex network body ECU) performs fade-in/fade-out control of the door mirror foot lights.



b.

The door mirror foot light control has the following control functions:

Function Outline
Actuation Area-linked*1 When all of the following conditions are met, the lights that operate fade-in:
·

The ignition switch is off.

·

All doors are closed.

·

A key is detected in the actuation area.


When the following condition is met, the lights that operate fade-out:
·

A key is not detected in the actuation area.


Door Lock/Unlock-linked When all of the following conditions are met, the lights that operate fade-in:
·

The ignition switch is off.

·

All doors are closed.

·

Any door is unlocked when all doors are locked.


When either of the following conditions is met, the lights that operate fade-out:
·

All doors are locked when all doors are closed and any door is unlocked.

·

All doors are locked again when all doors are closed and locked.


Ignition Switch-linked When the following condition is met, the lights that operate fade-out:
·

The ignition switch is ON.


Delay When approximately 15 seconds elapse after any of the following conditions are met, the lights that operate fade-out:
·

An actuation area-linked function is used.*1

·

The door unlock-linked function is active.



*1: w/ Entry and Start System




FOLLOW ME HOME SYSTEM (w/ Follow Me Home System)


a.

The follow me home system is designed to illuminate the low beam headlights for approximately 30 seconds after the vehicle is parked.

i.

This system is controlled by the main body ECU (multiplex network body ECU).


ii.

This system is enabled when the following conditions are met:

·

The ignition switch is off.

·

The light control switch is in the AUTO position.

·

The light control switch is pulled to flash the headlights once.





LANE CHANGE FLASHER CONTROL


a.

This control is performed by the combination meter assembly.


b.

When the headlight dimmer switch assembly (turn signal switch) is moved to the lane change position (it is not necessary to hold the switch) during a lane change, the turn signal light flashes a specified number of times.


c.

While the turn signal light is flashing after the headlight dimmer switch assembly (turn signal switch) has been moved to the lane change position, the turn signal light turns off if the headlight dimmer switch assembly (turn signal switch) is moved in the opposite direction.



INTELLIGENT ADAPTIVE FRONT-LIGHTING SYSTEM (w/ AFS)


a.

Function of main components.

Component Function
Headlight ECU Sub-assembly LH Receives various signals, calculates the target lighting angle, and actuates the headlight swivel motor (LH side).
Headlight ECU Sub-assembly RH Receives various signals, calculates the target lighting angle, and actuates the headlight swivel motor (RH side).
Headlight Swivel Motor LH/RH
·

Driven by the headlight ECU sub-assembly LH/RH and the headlight swivel motor moves the low beam to vary its angle calculated by the headlight ECU sub-assembly LH/RH.

·

Driven by the headlight ECU Sub-assembly LH/RH and the headlight swivel motor moves the low beam left or right to the angle calculated by the headlight ECU sub-assembly LH/RH.


Steering Sensor Sends the steering angle signal to the headlight ECU sub-assembly LH.
Main Body ECU (Multiplex Network Body ECU) Receives a light control switch signal and transmits it to the headlight ECU sub-assembly LH.
Brake Booster with Master Cylinder Assembly
·

Skid Control ECU


Receives speed sensor signals and transmits it to the headlight ECU sub-assembly LH.
Headlight Dimmer Switch Assembly
·

Light Control Switch


Sends a light control switch position signal to the main body ECU (multiplex network body ECU).
ECM Sends the shift position signals to the headlight ECU sub-assembly LH.
Combination Meter Assembly Flashes the AFS OFF indicator light and displays a warning message when a malfunction is detected in the intelligent Adaptive Front-lighting System (AFS).


b.

System control.

i.

Low Speed Control

·

The headlight ECU sub-assembly LH performs low speed control when all of the following conditions are met:

-

Engine is running.

-

Vehicle is moving forward at a speed of 10 km/h (6 mph) or more.

-

Vehicle is moving forward at a speed of less than 30 km/h (19 mph).

-

Steering angle is 6 degrees or more.

-

Low beam headlights are on.



Swivel Angle Range (for LHD)
Driving Condition Low Beam
Left Right
Right Turn 0° Fixed 0° to 10° to Right
Left Turn 0° to 15° to Left 0° Fixed

Swivel Angle Range (for RHD)
Driving Condition Low Beam
Left Right
Right Turn 0° Fixed 0° to 15° to Right
Left Turn 0° to 10° to Left 0° Fixed


ii.

Medium-to-High Speed Control

·

The headlight ECU sub-assembly LH performs medium-to-high speed control when all of the following conditions are met:

-

Engine is running.

-

Vehicle is moving forward at a speed of 30 km/h (19 mph) or more.

-

Steering angle is 7.5 degrees or more.

-

Low beam headlights are on.



Swivel Angle Range (for LHD)
Driving Condition Low Beam
Left Right
Right Turn 0° to 5° to Left 0° to 10° to Right
Left Turn 0° to 15° to Left 0° to 7.5° to Right

Swivel Angle Range (for RHD)
Driving Condition Low Beam
Left Right
Right Turn 0° to 7.5° to Left 0° to 15° to Right
Left Turn 0° to 10° to Left 0° to 7.5° to Right


iii.

Operation Stop Condition

·

The headlight ECU sub-assembly LH stops performing control when any of the following conditions is met:

-

Engine stopped.

-

Vehicle is moving forward at a speed of less than 5 km/h (3 mph).

-

Steering angle is less than 6 degrees.

-

Low beam headlights are off.

-

Shift position in R or N.





c.

Diagnosis.

i.

When the headlight ECU sub-assembly detects a malfunction in the intelligent adaptive front-lighting system (AFS), Diagnostic Trouble Codes (DTCs) are stored in memory.


ii.

The DTCs can be read using the GTS. For details, refer to the Repair Manual.