CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 Connectors | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *a | 2 Connectors | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 1 Connector | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *a | 1 Connector | - | - |
Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3F-1 - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| 3K-1 - Body ground | B-R - Body ground | Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3D-3 - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3H-30 - Body ground | G - Body ground | Taillights and license plate lights drive output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off*1 | Below 1 V | |||
| 3A-52 - Body ground | L - Body ground | Front fog light drive output | Light control switch in tail or head position, fog light switch in front position | Below 1 V |
| Light control switch in tail or head position, fog light switch off | 11 to 14 V | |||
| 3H-21 - Body ground*2 | BE - Body ground | Rear fog light drive output | Light control switch in tail or head position, fog light switch in rear position | 11 to 14 V |
| Light control switch in tail or head position, fog light switch off | Below 1 V | |||
| 3F-31 - Body ground | G - Body ground | H-LP LH relay drive output | Ignition switch off | 11 to 14 V |
| Ignition switch ON | Below 1 V | |||
| F15-1 (DIM) - Body ground | Y - Body ground | H-LP RH relay drive output | Ignition switch off | 11 to 14 V |
| Ignition switch ON | Below 1 V | |||
| F15-8 (A) - Body ground | W - Body ground | Light control switch AUTO position signal input | Light control switch in AUTO position | Below 1 V |
| Light control switch not in AUTO position | Pulse generation | |||
| F15-10 (HF) - Body ground | LG - Body ground | Dimmer switch high flash position signal input | Dimmer switch in high flash position | Below 1 V |
| Dimmer switch not in high flash position | Pulse generation | |||
| F15-12 (HEAD) - Body ground | L - Body ground | Light control switch head position input | Light control switch in head position | Below 1 V |
| Light control switch not in head position | Pulse generation | |||
| F15-19 (CLTB) - F15-21 (CLTE) | G - V | Automatic light control sensor power supply output | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V | |||
| F15-20 (CLTS) - Body ground | BE - Body ground | Automatic light control sensor signal input | Ignition switch off | Below 1 V |
| Automatic light control system operating | Communication waveform generation
(See waveform 1) |
|||
| F15-22 (TAIL) - Body ground | Y - Body ground | Light control switch tail position signal input | Light control switch in tail or head position | Below 1 V |
| Light control switch not in tail or head position | Pulse generation | |||
| F15-23 (RFOG) - Body ground*2 | W - Body ground | Fog light switch rear position input | Fog light switch in rear position | Below 1 V |
| Fog light switch off | Pulse generation | |||
| F15-24 (HU) - Body ground | GR - Body ground | Dimmer switch high position signal input | Dimmer switch in high position | Below 1 V |
| Dimmer switch not in high position | Pulse generation | |||
| F15-26 (FFOG) - Body ground | R - Body ground | Fog light switch front position input | Fog light switch in front position | Below 1 V |
| Fog light switch off | Pulse generation | |||
| F16-4 (MILE) - Body ground*3 | R - Body ground | Door mirror foot lights drive output | Door mirror foot light illuminates | 11 to 14 V |
| Door mirror foot light off | Below 3 V |
*1: If the light switch has no OFF position, set the light switch to "Auto" with the Lo beam turned off. If the Lo beam is illuminated, shine a fluorescent light or other light source onto the light sensor to enter daytime mode.
*2: w/ Rear Fog Light
*3: w/ Door Mirror Foot Light
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | F15-20 (CLTS) - Body ground |
| Tool setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Ignition switch on (IG) |
The communication waveform changes according to the surrounding brightness.
CHECK HEADLIGHT ECU SUB-ASSEMBLY LH
| *A | for TMC Made | *B | for TMMT Made |
Disconnect the A16*1 or A95*2 headlight ECU sub-assembly LH connector.
*1: for TMC Made
*2: for TMMT Made
Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A16-4 (IG) - Body ground | V - Body ground | Engine power supply | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 11 to 14 V | |||
| A16-13 (ECUB) - Body ground | L - Body ground | Battery power supply | Light control switch off | Below 1 V |
| Light control switch in tail or head position | 11 to 14 V | |||
| A16-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A95-4 (IG) - Body ground | V - Body ground | Engine power supply | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 11 to 14 V | |||
| A95-13 (ECUB) - Body ground | L - Body ground | Battery power supply | Light control switch off | Below 1 V |
| Light control switch in tail or head position | 11 to 14 V | |||
| A95-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the A16*1 or A95*2 headlight ECU sub-assembly LH connector.
*1: for TMC Made
*2: for TMMT Made
Since the A16*1 or A95*2 headlight ECU sub-assembly LH connector is a waterproof type connector, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.
*1: for TMC Made
*2: for TMMT Made
Since the B headlight ECU sub-assembly LH connector is connected inside the headlight assembly, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.
Measure the voltage and check of pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A16-15 (SGR) - Body ground | BE - Body ground | Rear height control sensor sub-assembly LH ground | Ignition switch on (IG) | Below 1 Ω |
| A16-19 (LINS) - Body ground | SB - Body ground | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A16-16 (SBR) - A16-15 (SGR) | B - BE | Rear height control sensor sub-assembly LH power supply | Ignition switch on (IG) | 4.75 to 5.25 V |
| A16-17 (SHRL) - A16-15 (SGR) | W - BE | Rear height control sensor sub-assembly LH signal input | Ignition switch on (IG), vehicle unloaded, vehicle stopped | Approximately 2.5 V
(value decreases as the front of the vehicle is raised) |
| A16-20 (LINL) - Body ground | P - Body ground | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A16-21 (LCL) - Body ground | GR - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A16-22 (LCH) - Body ground | G - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A16-23 (CANL) - Body ground | SB - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A16-24 (CANH) - Body ground | Y - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| B-2 (LOLED2) - B-3 (LOLED1) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 11.2 to 17.7 V | |||
| B-3 (LOLED1) - Body ground | - | Low beam headlight LH drive ground | Low beam headlight LH on | Below 1 Ω |
| B-9 (ACTBI) - B-17 (ACTGI) | - | Headlight swivel and leveling motor LH power source | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 11 to 14 V | |||
| B-17 (ACTGI) - Body ground | - | Headlight swivel and leveling motor LH ground | Ignition switch on (IG) | Below 1 Ω |
| B-10 (DRL/CLL+) - B-1 (DRL/CLL-) | - | Parking light/daytime running light LH power source | Parking light and daytime running light LH off | Below 1 V |
| Parking light and daytime running light LH on | 11 to 14 V | |||
| B-1 (DRL/CLL-) - Body ground | - | Parking light/daytime running light LH ground | Parking light and daytime running light LH on | Below 1 Ω |
| B-19 (HI SOL+) - B-11 (HI SOL-) | - | High beam headlight LH drive output | High beam headlight LH off | Below 1 V |
| High beam headlight LH on | 11 to 14 V | |||
| B-11 (HI SOL-) - Body ground | - | High beam headlight LH ground | High beam headlight LH on | Below 1 Ω |
| C-4 (LINSI) - Body ground | - | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| C-13 (LINLI) - Body ground | - | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| B-16 (PWM1) - B-1 (DRL/CLL-) | - | Daytime running lights/clearance lights control signal output | Daytime running lights and clearance lights off | Below 1 V |
| Daytime running lights and clearance lights on | Pulse generation | |||
| B-10 (DRL/CLL+) - B-1 (DRL/CLL-) | - | Daytime running lights/clearance lights power source | Daytime running lights and clearance lights off | Below 1 V |
| Daytime running lights and clearance lights on | 11 to 14 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A95-15 (SGR) - Body ground | BE - Body ground | Rear height control sensor sub-assembly LH ground | Ignition switch on (IG) | Below 1 Ω |
| A95-19 (LINS) - Body ground | SB - Body ground | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A95-16 (SBR) - A95-15 (SGR) | B - BE | Rear height control sensor sub-assembly LH power supply | Ignition switch on (IG) | 4.75 to 5.25 V |
| A95-17 (SHRL) - A95-15 (SGR) | W - BE | Rear height control sensor sub-assembly LH signal input | Ignition switch on (IG), vehicle unloaded, vehicle stopped | Approximately 2.5 V
(value decreases as the front of the vehicle is raised) |
| A95-20 (LINL) - Body ground | P - Body ground | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A95-23 (CANL) - Body ground | SB - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A95-24 (CANH) - Body ground | L - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| B-2 (LOLED2) - B-3 (LOLED1) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 11.2 to 17.7 V | |||
| B-3 (LOLED1) - Body ground | - | Low beam headlight LH drive ground | Low beam headlight LH on | Below 1 Ω |
| B-9 (ACTBI) - B-17 (ACTGI) | - | Headlight swivel and leveling motor LH power source | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 11 to 14 V | |||
| B-17 (ACTGI) - Body ground | - | Headlight swivel and leveling motor LH ground | Ignition switch on (IG) | Below 1 Ω |
| B-10 (DRL/CLL+) - B-1 (DRL/CLL-) | - | Parking light/daytime running light LH power source | Parking light and daytime running light LH off | Below 1 V |
| Parking light and daytime running light LH on | 11 to 14 V | |||
| B-1 (DRL/CLL-) - Body ground | - | Parking light/daytime running light LH ground | Parking light and daytime running light LH on | Below 1 Ω |
| B-19 (HI SOL+) - B-11 (HI SOL-) | - | High beam headlight LH drive output | High beam headlight LH off | Below 1 V |
| High beam headlight LH on | 11 to 14 V | |||
| B-11 (HI SOL-) - Body ground | - | High beam headlight LH ground | High beam headlight LH on | Below 1 Ω |
| C-4 (LINSI) - Body ground | - | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| C-13 (LINLI) - Body ground | - | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| B-16 (PWM1) - B-1 (DRL/CLL-) | - | Daytime running lights/clearance lights control signal output | Daytime running lights and clearance lights off | Below 1 V |
| Daytime running lights and clearance lights on | Pulse generation | |||
| B-10 (DRL/CLL+) - B-1 (DRL/CLL-) | - | Daytime running lights/clearance lights power source | Daytime running lights and clearance lights off | Below 1 V |
| Daytime running lights and clearance lights on | 11 to 14 V |
CHECK HEADLIGHT ECU SUB-ASSEMBLY RH
Disconnect the A17 headlight ECU sub-assembly RH connector.
Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A17-4 (IG) - Body ground | V - Body ground | Engine power supply | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 11 to 14 V | |||
| A17-13 (ECUB) - Body ground | L - Body ground | Battery power supply | Light control switch off* | Below 1 V |
| Light control switch in tail or head position | 11 to 14 V | |||
| A17-12 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
*: If the light switch has no OFF position, set the light switch to "Auto" with the Lo beam turned off. If the Lo beam is illuminated, shine a fluorescent light or other light source onto the light sensor to enter daytime mode.
Reconnect the A17 headlight ECU sub-assembly RH connector.
Since the A17 headlight ECU sub-assembly RH connector is a waterproof type connector, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.
Since the B headlight ECU sub-assembly RH connector is connected inside the headlight assembly, the voltage cannot be measured and pulses cannot be checked for directly. The values listed are for reference only.
Measure the voltage and check of pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A17-19 (LINS) - Body ground | SB - Body ground | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A17-21 (LCL) - Body ground | GR - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| A17-22 (LCH) - Body ground | G - Body ground | CAN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| B-2 (LOLED2) - B-3 (LOLED1) | - | Low beam headlights drive output | Low beam headlights off | Below 1 V |
| Low beam headlights on | 13.38 to 19.62 V | |||
| B-3 (LOLED1) - Body ground | - | Low beam headlight RH drive ground | Low beam headlight RH on | Below 1 Ω |
| B-9 (ACTBI) - B-17 (ACTGI) | - | Headlight swivel and leveling motor RH power source | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | 11 to 14 V | |||
| B-17 (ACTGI) - Body ground | - | Headlight swivel and leveling motor RH ground | Ignition switch on (IG) | Below 1 Ω |
| B-10 (DRL/CLL+) - B-1 (DRL/CLL-) | - | Parking light/daytime running light RH power source | Parking light and daytime running light RH off | Below 1 V |
| Parking light and daytime running light RH on | 11 to 14 V | |||
| B-1 (DRL/CLL-) - Body ground | - | Parking light/daytime running light RH ground | Parking light and daytime running light RH on | Below 1 Ω |
| B-19 (HI SOL+) - B-11 (HI SOL-) | - | High beam headlight RH drive output | High beam headlight RH off | Below 1 V |
| High beam headlight RH on | 11 to 14 V | |||
| B-11 (HI SOL-) - Body ground | - | High beam headlight RH ground | High beam headlight RH on | Below 1 Ω |
| C-4 (LINSI) - Body ground | - | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| C-13 (LINLI) - Body ground | - | LIN communication line | Ignition switch off | Below 1 V |
| Ignition switch on (IG) | Pulse generation | |||
| B-16 (PWM1) - B-1 (DRL/CLL-) | - | Daytime running lights/clearance lights control signal output | Daytime running lights and clearance lights off | Below 1 V |
| Daytime running lights or clearance lights on | Pulse generation | |||
| B-10 (DRL/CLL+) - B-1 (DRL/CLL-) | - | Daytime running lights/clearance lights power source | Daytime running lights and clearance lights off | Below 1 V |
| Daytime running lights or clearance lights on | 11 to 14 V |
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU