Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Headlight ECU) › from 2019.09
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0407373 LIGHTING SYSTEM(w/ Headlight ECU) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Headlight ECU)  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives the hazard warning signal switch assembly on signal and controls the operation of the hazard warning lights.

WIRING DIAGRAM

E357709E01
5.125,2.823 7.146,3.052 2.021,0.229 10 false Combination Meter Assembly 5.135,2.635 7.146,2.833 2.01,0.198 10 false F5 4.979,1.292 6.917,1.5 1.938,0.208 10 false 3 5.167,1.323 5.646,1.563 0.479,0.24 10 false HAZ 5.792,1.438 5.99,1.719 0.198,0.281 10 false I/F 6.177,1.427 6.583,1.729 0.406,0.302 10 false CPU 3.021,1.313 4.958,1.521 1.938,0.208 10 false 4 1.865,1.302 3.802,1.51 1.938,0.208 10 false 1 2.042,1.302 3.979,1.51 1.938,0.208 10 false E 2.75,1.302 4.688,1.51 1.938,0.208 10 false TB 1.813,1.875 3.75,2.083 1.938,0.208 10 false F62 1.802,2.042 3.24,2.5 1.438,0.458 10 false Hazard Warning Signal Switch Assembly


CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard warning signal switch signal ON or OFF ON: Hazard warning signal switch on
OFF: Hazard warning signal switch off
-
Body Electrical > Combination Meter > Data List
Tester Display
Hazard Flasher Switch
50003 122 99
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.

Remove the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL


b.

Inspect the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>INSPECTION

OK:

Hazard warning signal switch assembly is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY OR BODY GROUND)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY OR BODY GROUND)
a.

Disconnect the F5 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F62-4 (TB) - F5-3 (HAZ) Always Below 1 Ω
F62-4 (TB) or F5-3 (HAZ) - Body ground Always 10 kΩ or higher
F62-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR