CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | Main Body ECU (Multiplex Network Body ECU) with 2 Connectors | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *a | 2 Connectors | - | - |
| *A | Main Body ECU (Multiplex Network Body ECU) with 1 Connector | - | - |
| *1 | Main Body ECU (Multiplex Network Body ECU) | - | - |
| *a | 1 Connector | - | - |
Disconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3F-1 - Body ground | W - Body ground | Battery power supply | Always | 11 to 14 V |
| 3K-1 - Body ground | B-R - Body ground | Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Measure the resistance on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3D-3 - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the instrument panel junction block assembly and main body ECU (multiplex network body ECU) connectors.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 3H-30 - Body ground | G - Body ground | Taillights and license plate lights drive output | Light control switch in tail or head position | 11 to 14 V |
| Light control switch off*1 | Below 1 V | |||
| 3A-52 - Body ground*2 | L - Body ground | Front fog light drive output | Light control switch in tail or head position, fog light switch in front position | Below 1 V |
| Light control switch in tail or head position, fog light switch off | 11 to 14 V | |||
| 3H-21 - Body ground*4 | BE - Body ground | Rear fog light drive output | Light control switch in tail or head position, fog light switch in rear position | 11 to 14 V |
| Light control switch in tail or head position, fog light switch off | Below 1 V | |||
| 3F-31 - Body ground | G - Body ground | H-LP LH relay drive output | Ignition switch off | 11 to 14 V |
| Ignition switch ON | Below 1 V | |||
| F15-1 (DIM) - Body ground | Y - Body ground | H-LP RH relay drive output | Ignition switch off | 11 to 14 V |
| Ignition switch ON | Below 1 V | |||
| F15-8 (A) - Body ground | W - Body ground | Light control switch AUTO position signal input | Light control switch in AUTO position | Below 1 V |
| Light control switch not in AUTO position | Pulse generation | |||
| F15-10 (HF) - Body ground | LG - Body ground | Dimmer switch high flash position signal input | Dimmer switch in high flash position | Below 1 V |
| Dimmer switch not in high flash position | Pulse generation | |||
| F15-12 (HEAD) - Body ground | L - Body ground | Light control switch head position input | Light control switch in head position | Below 1 V |
| Light control switch not in head position | Pulse generation | |||
| F15-19 (CLTB) - F15-21 (CLTE) | G - V | Automatic light control sensor power supply output | Ignition switch off | Below 1 V |
| 11 to 14 V | ||||
| F15-20 (CLTS) - Body ground | BE - Body ground | Automatic light control sensor signal input | Ignition switch off | Below 1 V |
| Automatic light control system operating | Communication waveform generation
(See waveform 1) |
|||
| F15-22 (TAIL) - Body ground | Y - Body ground | Light control switch tail position signal input | Light control switch in tail or head position | Below 1 V |
| Light control switch not in tail or head position | Pulse generation | |||
| F15-23 (RFOG) - Body ground*4 | W - Body ground | Fog light switch rear position input | Fog light switch in rear position | Below 1 V |
| Fog light switch off | Pulse generation | |||
| F15-24 (HU) - Body ground | GR - Body ground | Dimmer switch high position signal input | Dimmer switch in high position | Below 1 V |
| Dimmer switch not in high position | Pulse generation | |||
| F15-26 (FFOG) - Body ground*2 | R - Body ground | Fog light switch front position input | Fog light switch in front position | Below 1 V |
| Fog light switch off | Pulse generation | |||
| F16-4 (MILE) - Body ground*3 | R - Body ground | Door mirror foot lights drive output | Door mirror foot light illuminates | 11 to 14 V |
| Door mirror foot light off | Below 3 V |
*1: If the light switch has no OFF position, set the light switch to "Auto" with the Lo beam turned off. If the Lo beam is illuminated, shine a fluorescent light or other light source onto the light sensor to enter daytime mode.
*2: w/ Front Fog Light
*3: w/ Door Mirror Foot Light
*4: w/ Rear Fog Light
If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may be malfunctioning.
Waveform 1
| Item | Content |
|---|---|
| Tester Connection | F15-20 (CLTS) - Body ground |
| Tool setting | 2 V/DIV., 10 ms./DIV. |
| Condition | Ignition switch ON |
The communication waveform changes according to the surrounding brightness.
CHECK COMBINATION METER ASSEMBLY
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU