Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for TMC Made) › from 2019.09
RM32H0E _V1 General _059503 MAINTENANCE _0358316 REAR DISC BRAKE PAD(for TMC Made) A

MAINTENANCE  REAR DISC BRAKE PAD(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

The following procedure is for the LH side.

·

Use the same procedure for the RH side and LH side.



PROCEDURE

Hide 2.REMOVE REAR WHEEL

Hide 3.PERFORM REAR BRAKE PAD REPLACEMENT MODE

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 04466 5.REMOVE REAR DISC BRAKE PAD

CAUTION:
·
C368019

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.
C366000

Disconnect the No. 2 parking brake wire assembly from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the connector before performing this work.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




b.
C422658C01
2.802,2.219 3.115,2.417 0.313,0.198 10 false *a 2.479,0.885 2.792,1.083 0.313,0.198 10 false *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin, and remove the bolt.


c.
C368445

Pull the rear disc brake cylinder assembly upward.


d.

Remove the 2 rear disc brake pads from the rear disc brake cylinder mounting.


Hide 04946 6.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

a.
C418243C01
1.188,0.531 1.521,0.531 false 0.802,0.292 1.135,0.292 false 2.708,1.396 2.802,1.104 2.802,1.104 2.969,1.104 false 0.583,1.688 0.917,1.688 false 1.448,1.948 1.781,1.948 false 1.594,0.438 1.906,0.635 0.313,0.198 10 false *1 1.177,0.198 1.49,0.396 0.313,0.198 10 false *2 3.021,1.021 3.333,1.219 0.313,0.198 10 false *3 1.833,1.865 2.146,2.063 0.313,0.198 10 false *4 0.375,1.594 0.688,1.792 0.313,0.198 10 false *4
*1 Rear No. 1 Disc Brake Anti-squeal Shim
*2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Anti-squeal Shim
*4 Rear Disc Brake Pad Wear Indicator Plate


Remove the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim from the rear disc brake pad (Inner Side).


b.

Remove the rear disc brake anti-squeal shim from the rear disc brake pad (Outer Side).


c.
C366017

Using a screwdriver, remove the rear disc brake pad wear indicator plate from each rear disc brake pad.