Home › General › MAINTENANCE › REAR DISC BRAKE PAD (for TMC Made) › from 2019.09
RM32H0E _V1 General _059503 MAINTENANCE _0358316 REAR DISC BRAKE PAD(for TMC Made) A

MAINTENANCE  REAR DISC BRAKE PAD(for TMC Made)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

The following procedure is for the LH side.

·

Use the same procedure for the RH side and LH side.



PROCEDURE

Hide 04946 1.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

NOTICE:
·

When replacing worn rear disc brake pads, the rear disc brake anti-squeal shims and rear disc brake pad wear indicator plates must be replaced together with the rear disc brake pads.

·

Install each rear disc brake pad wear indicator plate in the correct position and direction.

·

Install the rear disc brake anti-squeal shims in the correct positions and directions.

·

Do not apply disc brake grease to the lining surface of the rear disc brake pad.



a.
C418241C01
0.781,1.073 1.313,1.073 true 2.344,0.823 2.76,0.823 true 2.875,0.729 3.188,0.885 0.313,0.156 10 false *a 0.552,0.979 0.865,1.135 0.313,0.156 10 false *b
*a Inner Side (Orange)
*b Outer Side (Yellow green)


Check the rear disc brake pad.

HINT:

If the rear disc brake pad has an identification mark, be sure to confirm the installation location.



b.
C406537C03
0,0 0,0 false
V100145

Disc Brake Grease


Apply disc brake grease to the inner side of the rear disc brake anti-squeal shim as shown in the illustration.


c.
C418243C02
1.188,0.531 1.521,0.531 false 0.802,0.292 1.135,0.292 false 2.708,1.396 2.802,1.104 2.802,1.104 2.969,1.104 false 0.583,1.688 0.917,1.688 false 1.448,1.948 1.781,1.948 false 2.583,1.917 2.583,1.75 2.583,1.75 2.76,1.615 false 1.594,0.438 1.906,0.635 0.313,0.198 10 false *1 1.177,0.198 1.49,0.396 0.313,0.198 10 false *2 3.021,1.021 3.333,1.219 0.313,0.198 10 false *3 1.833,1.865 2.146,2.063 0.313,0.198 10 false *4 0.375,1.594 0.688,1.792 0.313,0.198 10 false *4 2.49,1.938 2.802,2.135 0.313,0.198 10 false *a
*1 Rear No. 1 Disc Brake Anti-squeal Shim
*2 Rear No. 2 Disc Brake Anti-squeal Shim
*3 Rear Disc Brake Anti-squeal Shim
*4 Rear Disc Brake Pad Wear Indicator Plate
*a Claw


Install 2 new rear disc brake pad wear indicator plates to each rear disc brake pad.

NOTICE:

Install the rear disc brake pad wear indicator plate in the correct positions and direction.



d.

Install the rear No. 1 disc brake anti-squeal shim and rear No. 2 disc brake anti-squeal shim to rear disc brake pad (Inner Side).


e.

Install the rear disc brake anti-squeal shim to the rear disc brake pad (Outer Side).

NOTICE:

Install the rear disc brake anti-squeal shim so that it claw is toward the outside of the vehicle.



Hide 04466 2.INSTALL REAR DISC BRAKE PAD KIT

CAUTION:
·

Be careful not to get pinched by the rear disc brake cylinder assembly or other parts when installing the rear disc brake pads.

·
C368019

After lifting up the rear disc brake cylinder assembly, secure it in place before performing any work on it.

·

The rear disc brake cylinder assembly could fall, pinching hands or fingers and causing injury.



a.

Push back the rear disc brake piston.

NOTICE:
·

Make sure the brake fluid does not overflow from the reservoir.

·

Do not forcibly push in the rear disc brake piston.




b.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.

·

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.




c.
C422659C01
2.719,2.177 3.031,2.375 0.313,0.198 10 false *a 2.458,0.885 2.771,1.083 0.313,0.198 10 false *b
*a Hold
*b Turn


Hold the rear disc brake cylinder slide pin and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with a new bolt.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


d.

Connect the No. 2 parking brake wire assembly to the parking brake actuator assembly.


e.

Depress the brake pedal several times.


Hide 4.INSTALL REAR WHEEL