Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › ANTENNA CORD › 2019.09–2020.08
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0303547 ANTENNA CORD A

NAVIGATION / MULTI INFO DISPLAY  ANTENNA CORD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced the during antenna cord sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)

CAUTION:
B458500

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 55401E 1.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 55086 2.REMOVE NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)

Hide 55084E 3.REMOVE NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

Hide 86101 4.REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

Disengage the clamps to remove the antenna cord sub-assembly.

E353801C01
3.479,0.979 3.76,0.51 true 1.896,0.885 2.344,1 true 2.823,1.719 2.896,1.427 true 4.135,1.417 3.854,1.583 true 3.771,0.323 4.146,0.563 0.375,0.24 12 false *A 1.656,0.688 2.031,0.927 0.375,0.24 12 false *B 2.677,1.75 3.052,1.99 0.375,0.24 12 false *A 4.198,1.271 4.448,1.51 0.25,0.24 12 true *A
*A w/ USB Audio System *B w/ Manual (SOS) Switch



b.

w/ Manual (SOS) Switch:

i.

Disconnect the connector.



Hide 86101 5.REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

Disengage the clamps to remove the antenna cord sub-assembly.

E426190C01
1.49,1.354 1.792,1.625 true 0.448,0.76 0.677,1.115 true 0.417,1.865 0.99,1.74 true 1.865,1.563 2.156,1.802 0.292,0.24 12 false *A 0.24,0.552 0.531,0.792 0.292,0.24 12 false *A 1.042,1.615 1.333,1.854 0.292,0.24 12 false *A
*A w/ USB Audio System - -



Hide 63311C 6.REMOVE ROOF HEADLINING

Hide 86101J 7.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

for Type A:

i.

Remove each adhesive tape from the roof headlining.

E359077C03
0,0 0,0 false
V100155

Adhesive Tape
V100136

Front



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



b.

for Type B:

i.

Remove each adhesive tape from the roof headlining.

E353818C06
0,0 0,0 false
V100155

Adhesive Tape
V100136

Front



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



c.

for Type C:

i.

Remove each adhesive tape from the roof headlining.

E426191C01
0,0 0,0 false
V100155

Adhesive Tape
V100136

Front



ii.

Remove the No. 2 antenna cord sub-assembly from the roof headlining.



Hide 86101D 8.REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.

for Glass Antenna Type:

i.
E353812

Disconnect the connector of the No. 4 antenna cord sub-assembly.



b.
E353809

Disconnect the connector.


c.

Disengage the clamps.


d.

w/ Manual (SOS) Switch:

i.
E353811C03
2.115,0.896 2.448,0.896 true 1.104,1.5 0.771,1.5 true 2.448,0.792 2.688,0.99 0.24,0.198 10 true *a 0.521,1.396 0.76,1.594 0.24,0.198 10 true *b
*a Guide
*b Clamp


Disconnect the connector of the floor wire.


ii.

Remove the bolt.


iii.

Disengage the clamp and guide to remove the No. 3 antenna cord sub-assembly.



e.

w/o Manual (SOS) Switch:

i.
E353810C03
0.688,1.323 1.063,1.406 true 2.292,0.771 2.552,0.594 true 0.417,1.208 0.656,1.417 0.24,0.208 10 true *b 2.594,0.417 2.833,0.625 0.24,0.208 10 true *a
*a Guide
*b Clamp


Remove the bolt.


ii.

Disengage the clamp and guide to remove the No. 3 antenna cord sub-assembly.