The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor RH.
The door side airbag sensor RH and No. 2 side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
DTC B1633 is stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1633 | Curtain Shield Airbag Sensor Initialization Error (RH) | ·
The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1). ·
No. 2 side airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
No. 2 side airbag sensor RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||||||
|---|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | Pattern 6 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) | ○ | - | - | - | - | - |
| The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) | - | ○ | - | - | - | - | |
| The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) | - | - | ○ | - | - | - | |
| The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) | - | - | - | ○ | - | - | |
| No. 2 side airbag sensor RH malfunction | - | - | - | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | - | - | - | ○ | |
| Detection Time | - | - | - | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for history DTCs.
Codes other than history DTC B1632 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| History DTC B1632 is not output. | A |
| History DTC B1632 is output. | B |
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH) |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M57-4 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| M57-3 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M57-4 (BCR+) - M57-3 (BCR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M57-4 (BCR+) - M57-3 (BCR-) | Always | 1 MΩ or higher |
| M57-4 (BCR+) - Body ground | Always | 1 MΩ or higher |
| M57-3 (BCR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Connect the connectors that link the floor wire and front door wire RH.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M57-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| M57-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M57-1 (BDR+) - M57-2 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M57-1 (BDR+) - M57-2 (BDR-) | Always | 1 MΩ or higher |
| M57-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| M57-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Side Airbag Sensor LH |
| *2 | Airbag Sensor assembly |
Connect the connectors to the door side airbag sensor RH and airbag sensor assembly.
Interchange the No. 2 side airbag sensor RH with LH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1633 is output. | A |
| DTC B1638 is output. | B |
| DTCs B1633 and B1638 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor RH and LH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Front Door Wire RH) |
Disconnect the floor wire connector from the front door wire RH.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| IM1-40 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | 1 MΩ or higher |
| IM1-22 (BDR+) - Body ground | Always | 1 MΩ or higher |
| IM1-40 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG