The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor LH.
The door side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the No. 2 side airbag sensor LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1635 | Curtain Shield Airbag Sensor (LH) | ·
No. 2 side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 side airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B1637 | Curtain Shield Airbag Sensor Lost Communication (LH) | ·
No. 2 side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
No. 2 side airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction Status | No. 2 side airbag sensor LH malfunction | ○ | - |
| Airbag sensor assembly malfunction | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction Status | No. 2 side airbag sensor LH malfunction | ○ | - |
| Airbag sensor assembly malfunction | - | ○ | |
| Detection Time | - | - | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| *1 | No. 2 Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B1630, B1632, B1635 and B1637 may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B1635 or B1637 is output. | A |
| DTC B1630 or B1632 is output. | B |
| DTCs B1630, B1632, B1635 and B1637 are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING