The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and No. 2 side airbag sensor LH.
The door side airbag sensor LH and No. 2 side airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B167B | Lost Communication with Front Door Pressure Sensor LH | ·
The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). ·
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). ·
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). ·
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). ·
No. 2 side airbag sensor LH malfunction ·
Door side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire LH ·
No. 2 side airbag sensor LH ·
Door side airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B167C | Front Door Pressure Sensor LH Initialization Incomplete | ·
The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1). ·
The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1). ·
The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1). ·
The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1). ·
No. 2 side airbag sensor LH malfunction ·
Door side airbag sensor LH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire LH ·
No. 2 side airbag sensor LH ·
Door side airbag sensor LH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) | ○ | - | - | - |
| The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) | - | ○ | - | - | |
| The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) | - | - | ○ | - | |
| The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) | - | - | - | ○ | |
| Detection Time | - | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 5 | Pattern 6 | Pattern 7 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | No. 2 side airbag sensor LH malfunction | ○ | - | - |
| Door side airbag sensor LH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | |||||
|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) | ○ | - | - | - |
| The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) | - | ○ | - | - | |
| The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) | - | - | ○ | - | |
| The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) | - | - | - | ○ | |
| Detection Time | - | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 5 | Pattern 6 | Pattern 7 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | No. 2 side airbag sensor LH malfunction | ○ | - | - |
| Door side airbag sensor LH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the door side airbag sensor LH and No. 2 side airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the door side airbag sensor LH and No. 2 side airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH) |
| *b | Front view of wire harness connector
(to Door Side Airbag Sensor LH) |
Connect the connectors that link the floor wire and front door wire LH.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M15-1 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| M15-2 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M15-1 (BDL+) - M15-2 (BDL-) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M15-1 (BDL+) - M15-2 (BDL-) | Always | 1 MΩ or higher |
| M15-1 (BDL+) - Body ground | Always | 1 MΩ or higher |
| M15-2 (BDL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 2 Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the door side airbag sensor LH.
Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B167B or B167C is output. | A |
| DTC B166D or B166E is output. | B |
| DTCs B166D, B166E, B167B and B167C are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor LH |
Interchange the door side airbag sensor LH with RH and connect the connectors.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B167B or B167C is output. | A |
| DTC B166D or B166E is output. | B |
| DTCs B166D, B166E, B167B and B167C are not output. | C |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor LH |
| *3 | Front Door Wire LH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH) |
| *b | Front view of wire harness connector
(to Front Door Wire LH) |
Disconnect the floor wire connector from the front door wire LH.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| JM1-22 (BDL+) - Body ground | Ignition switch ON | Below 1 V |
| JM1-40 (BDL-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| JM1-22 (BDL+) - JM1-40 (BDL-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| JM1-22 (BDL+) - JM1-40 (BDL-) | Always | 1 MΩ or higher |
| JM1-22 (BDL+) - Body ground | Always | 1 MΩ or higher |
| JM1-40 (BDL-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG