Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0299845 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the meter circuit plate to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E235207E24
5.063,1.771 5.448,1.938 0.385,0.167 10 false F4 3.75,1.448 4.667,1.615 0.917,0.167 10 false Other ECUs 5.198,1.021 5.583,1.188 0.385,0.167 10 false +S 5.021,0.938 5.208,1.104 0.188,0.167 10 false 6 1.688,1.021 2.031,1.25 0.344,0.229 10 false SPD 2.063,0.938 2.281,1.115 0.219,0.177 10 false 11 5.063,1.938 6.313,2.292 1.25,0.354 10 false Combination Meter Assembly 0.948,1.771 1.333,1.938 0.385,0.167 10 false F152 0.938,1.927 2.177,2.563 1.24,0.635 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.

Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.
E286967C38
1.5,0.333 1.917,0.583 0.417,0.25 1.76,1.302 2.667,0.667 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.615,0.385 2.073,0.583 0.458,0.198 10 false F4 2.667,0.5 3.125,0.698 0.458,0.198 10 false +S 1.115,3.844 1.427,4.042 0.313,0.198 10 false A 2.781,3.594 3.24,3.792 0.458,0.198 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Connect an oscilloscope to terminal F4-6 (+S) and body ground.


iii.

Turn the ignition switch ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F4-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.
E286967C44
1.5,0.333 1.917,0.583 0.417,0.25 1.135,1.333 0.74,0.74 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.552,0.385 2.01,0.583 0.458,0.198 10 false F152 0.51,0.583 0.969,0.781 0.458,0.198 10 false SPD 1.115,3.844 1.427,4.042 0.313,0.198 10 false A 2.781,3.594 3.24,3.792 0.458,0.198 10 false GND
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Connect an oscilloscope to terminal F152-11 (SPD) and body ground.


iii.

Turn the ignition switch ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal F152-11 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F152 stereo component amplifier assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F152-11 (SPD) - F4-6 (+S) Always Below 1 Ω
F152-11 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR