Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › INTELLIGENT MANUAL TRANSMISSION SWITCH › from 2019.09
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292327 INTELLIGENT MANUAL TRANSMISSION SWITCH G

EC6A MANUAL TRANSMISSION / TRANSAXLE  INTELLIGENT MANUAL TRANSMISSION SWITCH  INSPECTION  


PROCEDURE

Hide 84390B 1.INSPECT INTELLIGENT MANUAL TRANSMISSION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for LHD)

a.

Check the resistance.

i.
C366035C25
2.302,1.438 2.667,1.833 true 1.719,1.479 1.333,1.865 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.719,1.813 3.198,2.052 0.479,0.24 10 false E 1.229,1.865 1.406,2.031 0.177,0.167 10 false S
*a Component without harness connected
(Intelligent Manual Transmission Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
11 (S) - 8 (E) Switch pushed Below 1 Ω
11 (S) - 8 (E) Switch not pushed 10 kΩ or higher


If the result is not as specified, replace the intelligent manual transmission switch (electric parking brake switch assembly).



b.

Check that the illumination illuminates.

i.
C366035C26
2.302,1.219 2.885,0.802 true 1.146,1.219 0.583,0.833 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.948,0.719 3.427,0.958 0.479,0.24 10 false ILL- 0.24,0.75 0.531,0.917 0.292,0.167 10 false ILL+
*a Component without harness connected
(Intelligent Manual Transmission Switch (Electric Parking Brake Switch Assembly))


Apply battery voltage between the terminals of the switch, and check the illumination condition of the intelligent manual transmission switch (electric parking brake switch assembly).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the intelligent manual transmission switch (electric parking brake switch assembly).



Hide 84390B 2.INSPECT INTELLIGENT MANUAL TRANSMISSION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (for RHD)

a.

Check the resistance.

i.
C366035C27
2.302,1.438 2.667,1.833 true 1.375,1.469 0.99,1.854 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.719,1.813 3.198,2.052 0.479,0.24 10 false E 0.865,1.865 1.042,2.031 0.177,0.167 10 false S
*a Component without harness connected
(Intelligent Manual Transmission Switch (Electric Parking Brake Switch Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 (S) - 8 (E) Switch pushed Below 1 Ω
13 (S) - 8 (E) Switch not pushed 10 kΩ or higher


If the result is not as specified, replace the intelligent manual transmission switch (electric parking brake switch assembly).



b.

Check that the illumination illuminates.

i.
C366035C26
2.302,1.219 2.885,0.802 true 1.146,1.219 0.583,0.833 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.948,0.719 3.427,0.958 0.479,0.24 10 false ILL- 0.24,0.75 0.531,0.917 0.292,0.167 10 false ILL+
*a Component without harness connected
(Intelligent Manual Transmission Switch (Electric Parking Brake Switch Assembly))


Apply battery voltage between the terminals of the switch, and check the illumination condition of the intelligent manual transmission switch (electric parking brake switch assembly).

Standard:
Measurement Condition Specified Condition
Battery positive (+) → 7 (ILL+)
Battery negative (-) → 1 (ILL-)
Illuminates


If the result is not as specified, replace the intelligent manual transmission switch (electric parking brake switch assembly).