Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › 2018.05–2019.09
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


E415756C02
3.396,2.563 3.823,2.823 0.427,0.26 3.385,0.604 3.813,0.865 0.427,0.26 3.469,2.615 4.083,2.813 0.615,0.198 10 false F137 3.479,0.656 4.094,0.854 0.615,0.198 10 false F22 3.885,0.625 4.26,0.865 0.375,0.24 12 false *A 3.896,2.594 4.271,2.833 0.375,0.24 12 false *B
*A for 12 Pin Type *B for 16 Pin Type


a.

Disconnect the F22*1 or F137*2 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F22-1 (+B) - F22-5 (GND)*1 Input W - W-B Battery Always 11 to 14 V +B
F137-4 (+B) - F137-12 (GND)*2 Input W - W-B Battery Always 11 to 14 V +B
F22-2 (IG) - F22-5 (GND)*1 Input B - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
F137-6 (IG) - F137-12 (GND)*2 Input B - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
F22-3 (KSW) - F22-5 (GND)*1 Input V - W-B Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω
F137-5 (KSW) - F137-12 (GND)*2 Input V - W-B Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher Key SW/B2780
Key in ignition key cylinder Below 1 Ω
F22-5 (GND) - Body ground*1 - W-B - Body ground Ground Always Below 1 Ω -
F137-12 (GND) - Body ground*2 - W-B - Body ground Ground Always Below 1 Ω -

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the F22*1 or F137*2 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F22-8 (IND) - F22-5 (GND)*1 Output P - W-B Security indicator signal No key in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
F137-8 (IND) - F137-12 (GND)*2 Output P - W-B Security indicator signal No key in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Key in ignition key cylinder (immobiliser system unset) Below 1 V
F22-9 (D) - F22-5 (GND)*1 Input/Output SB - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
F137-9 (D) - F137-12 (GND)*2 Input/Output SB - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
F22-4 (ANT1) - F22-5 (GND)*1 Input/Output V - W-B Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
F137-2 (ANT1) - F137-12 (GND)*2 Input/Output V - W-B Transponder key amplifier power source No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 1)
F22-15 (ANT2) - F22-5 (GND)*1 Input/Output W - W-B Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
F137-3 (ANT2) - F137-12 (GND)*2 Input/Output W - W-B Transponder key amplifier communication signal No key in ignition key cylinder 4 to 6 V -
Within 3 seconds of inserting key into ignition key cylinder Pulse generation
(See waveform 2)
F22-12 (EFII) - F22-5 (GND)*1 Output G - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
-
F137-10 (EFII) - F137-12 (GND)*2 Output G - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 3)
-
F22-13 (EFIO) - F22-5 (GND)*1 Input R - W-B ECM output signal Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 4)
F137-11 (EFIO) - F137-12 (GND)*2 Input R - W-B ECM output signal Ignition switch off Below 1 V -
Ignition switch ON Pulse generation
(See waveform 4)

If the result is not as specified, the transponder key ECU assembly may be malfunctioning.


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Tester Connection F22-4 (ANT1) - F22-5 (GND)*1
F137-2 (ANT1) - F137-12 (GND)*2
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


ii.

Waveform 2 (Reference)

B329910N02
5.75,0.854 6.208,1.052 0.458,0.198 10 GND

Tester Connection F22-15 (ANT2) - F22-5 (GND)*1
F137-3 (ANT2) - F137-12 (GND)*2
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting key into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F22-12 (EFII) - F22-5 (GND)*1
F137-10 (EFII) - F137-12 (GND)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Tester Connection F22-13 (EFIO) - F22-5 (GND)*1
F137-11 (EFIO) - F137-12 (GND)*2
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON




*1: for 16 Pin Type

*2: for 12 Pin Type


CHECK ECM


a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

i.

for 8NR-FTS:

A384862E05
2.417,0.75 2.917,1 0.5,0.25 5.323,0.75 5.833,1 0.51,0.25 2.542,0.802 3,1 0.458,0.198 10 false C62 5.427,0.802 5.885,1 0.458,0.198 10 false A38

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C62-53 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A38-45 (IMO) - C62-53 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Ignition switch off 11 to 14 V -
A38-45 (IMO) - C62-53 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of engine start or within 3 seconds of ignition switch turned ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
-
A38-28 (IMI) - C62-53 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Ignition switch off 11 to 14 V -
A38-28 (IMI) - C62-53 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Ignition switch turned on (IG) using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
-


ii.

for 3ZR-FAE:

A384862E06
2.417,0.75 2.917,1 0.5,0.25 5.323,0.75 5.833,1 0.51,0.25 2.542,0.802 3,1 0.458,0.198 10 false C63 5.427,0.802 5.885,1 0.458,0.198 10 false A38

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C63-59 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A38-45 (IMO) - C63-59 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Ignition switch off 11 to 14 V -
A38-45 (IMO) - C63-59 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of engine start or within 3 seconds of ignition switch turned ON after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
-
A38-28 (IMI) - C63-59 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Ignition switch off 11 to 14 V -
A38-28 (IMI) - C63-59 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Ignition switch turned ON using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
-



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection
·

A38-45 (IMO) - C62-53 (E1)*1

·

A38-45 (IMO) - C63-59 (E1)*2


Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned ON after cable disconnected and reconnected to battery

*1: for 8NR-FTS

*2: for 3ZR-FAE



ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection
·

A38-28 (IMI) - C62-53 (E1)*1

·

A38-28 (IMI) - C63-59 (E1)*2


Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch turned ON using registered electrical key transmitter sub-assembly

*1: for 8NR-FTS

*2: for 3ZR-FAE