Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2020.08–2021.09
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK ECM


C367116N04
2.417,0.167 2.917,0.417 0.5,0.25 5.5,0.167 6,0.417 0.5,0.25 2.552,0.198 3.01,0.396 0.458,0.198 10 false C62 5.635,0.198 6.094,0.396 0.458,0.198 10 false A38

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A38-9 (STP) - C62-53 (E1) G - W-B*1
R - W-B*2
Stop light switch assembly signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit Cruise control main switch (ON/OFF button) not pushed 1 MΩ or higher
Cruise control main switch (ON/OFF button) pushed Below 2.5 Ω
+RES switch ON 235 to 245 Ω
-SET switch ON 617 to 643 Ω
A38-55 (CCS) - C62-53 (E1) SB - W-B Cruise control main switch circuit CANCEL switch ON 1509 to 1571 Ω
Ignition switch to ON, brake pedal depressed Below 1 V
A38-10 (ST1-) - C62-53 (E1) LG - W-B*1
G - W-B*2
Stop light switch assembly signal Ignition switch to ON, brake pedal released 11 to 14 V

*1: for TMC Made

*2: for TMMT Made



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY


NOTICE:
·

Turning the ignition switch to ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the millimeter wave radar sensor assembly connector.



A402620E32
3.365,0.063 3.792,0.302 0.427,0.24 3.49,0.094 3.948,0.292 0.458,0.198 10 false A2

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-8 (IGB) - A2-1 (SGND) B - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A2-1 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω



CHECK FORWARD RECOGNITION CAMERA


NOTICE:
·

Turning the ignition switch ON with connectors disconnected may cause DTCs to be stored. Make sure to clear the DTCs after inspection has been performed.

·

Do not apply excessive force to the forward recognition camera connector.



B472992E31
2.073,0.833 2.458,1.042 0.385,0.208 2.167,0.844 2.479,1.042 0.313,0.198 10 false R5

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-3 (LKSW) - R5-10 (GND) SB - W-B*1
R - W-B*2
Steering pad switch assembly signal (distance control signal) Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) on Below 1 V
Ignition switch ON, steering pad switch assembly (vehicle-to-vehicle distance control switch) off 4.75 to 5.25 V
R5-7 (IGB) - R5-10 (GND) B - W-B Power source Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
R5-8 (BZ) - R5-10 (GND) P - W-B*1
B - W-B*2
Pre-collision city buzzer output Ignition switch ON buzzer not sounding 11 to 14 V
Ignition switch ON buzzer sounding Below 1 V
R5-10 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

*1: for TMC Made

*2: for TMMT Made