Home › Engine / Hybrid System › CRUISE CONTROL › FRONT CAMERA SYSTEM › from 2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0441733 FRONT CAMERA SYSTEM U

CRUISE CONTROL  FRONT CAMERA SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Reference Value" due are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Data List.


e.

Read the Data List according to the display on the GTS.

Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - - - Cannot be used
Total Distance Traveled - Unit - - - Cannot be used
Vehicle Information (Steering Wheel Position) Vehicle information (steering wheel position) stored in forward recognition camera Unknown / Left / Right Actual steering wheel position displayed If the value of this item differs from the specifications of the vehicle, a forward recognition camera which was installed to another vehicle may be installed or the forward recognition camera may be malfunctioning.
HV/EV Equipped Information Vehicle information (powertrain type) stored in forward recognition camera Non-HV/EV / HV/EV Non-HV/EV: Conventional vehicle
HV/EV: Hybrid vehicle
If the value of this item differs from the specifications of the vehicle, a forward recognition camera which was installed to another vehicle may be installed or the forward recognition camera may be malfunctioning.
Buzzer (Line) Equipped Information Existence of forward recognition camera buzzer Absent / Present Absent: Not equipped
Present: Equipped
If the value of this item differs from the specifications of the vehicle, a forward recognition camera which was installed to another vehicle may be installed or the forward recognition camera may be malfunctioning.
IG Status Information - - - Cannot be used
Online Calibration Angle (Horizontal) - - - Cannot be used
Online Calibration Angle (Vertical) - - - Cannot be used
Online Calibration Angle (Roll Angle) - - - Cannot be used
Front Recognition Camera Axis Adjusted Status - - - Cannot be used
Front Recognition Camera Low Temperature Existence of forward recognition camera low voltage malfunction Not Low Temperature / Low Temperature Not Low Temperature: Approximately -30°C (-22°F) or more
Low Temperature: Less than approximately -30°C (-22°F)
·

If the value of this item is "Low Temperature", "Front Camera Unavailable" is displayed on the multi-information display. If system operation does not return even after warming the cabin, the forward recognition camera may be malfunctioning.

·

If the value of this item is "Low Temperature", Vehicle Control History X2016 is stored.


Front Recognition Camera High Temperature 1 Existence of forward recognition camera high voltage malfunction Not High Temperature / High Temperature Not High Temperature: Less than approximately 80°C (176°F)
High Temperature: Approximately 80°C (176°F) or more
·

If the value of this item is "High Temperature", the front camera system is temporarily unavailable. If system operation does not return even after cooling the cabin for 10 minutes or more, the forward recognition camera may be malfunctioning.

·

If the value of this item is "High Temperature", Vehicle Control History X2016 is stored.


HINT:

During summer time, it is possible for the windshield glass to exceed 100°C (212°F).


Online Axis Alignment Error Code 31 Indicates whether online axis alignment error code 31 is present Not Detected / Detected Not Detected: error code not detected
Detected: error code 31 is detected
If this item is "Detected", it can be inferred that the vehicle speed at the start of online axis alignment was in excess of 5 km/h (3 mph), and online axis adjustment did not start.
Online Axis Alignment Error Code 32 Indicates whether online axis alignment error code 32 is present Not Detected / Detected Not Detected: error code not detected
Detected: error code 32 is detected
If this item is "Detected", it can be inferred that during online axis alignment, the field of view of the forward recognition camera was obstructed, causing online axis alignment to fail.
Online Axis Alignment Error Code 33 Indicates whether online axis alignment error code 33 is present Not Detected / Detected Not Detected: error code not detected
Detected: error code 33 is detected
If this item is "Detected", it can be inferred that during online axis alignment, DTCs or vehicle control history (RoB) occurred, causing online axis alignment to fail.
Online Axis Alignment Error Code 34 Indicates whether online axis alignment error code 34 is present Not Detected / Detected Not Detected: error code not detected
Detected: error code 34 is detected
If this item is "Detected", it can be inferred that the FOE value calculated via online axis alignment exceeded the normal range, causing online axis alignment to fail.
Online Axis Alignment Error Code 35 Indicates whether online axis alignment error code 35 is present Not Detected / Detected Not Detected: error code not detected
Detected: error code 35 is detected
If this item is "Detected", it can be inferred that the FOE value calculated via online axis alignment could not be correctly written to memory.
Heater Available Information Existence of forward recognition hood Absence / Presence Absence: w/o forward recognition hood
Presence: w/ forward recognition hood
The forward recognition camera checks its electrical connectivity with the heater wire. If this item is "Absence", a new forward recognition camera may have been installed with the heater wire disconnected.
Heater Control Permit Forward recognition hood control permission Not Allow / Allow Not Allow: Forward recognition hood control prohibited
Allow: Forward recognition hood control activated
If this item is "Prohibited", the following conditions are possible:
·

There is no heater wire.

·

The forward recognition camera has stored a DTC.

·

The forward recognition camera has stored vehicle control history.


Heater Control Forward recognition hood control state Not Control / Under Control Not Control: Forward recognition hood control not performed
Under Control: Forward recognition hood control being performed
If the heater wire control permission item is "Permitted" and the ambient temperature is 10°C (50°F) or less, this item will cycle between "Not Control" and "Under Control".