Home › Engine / Hybrid System › CRUISE CONTROL › FRONT RADAR SENSOR SYSTEM › from 2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0441735 FRONT RADAR SENSOR SYSTEM U

CRUISE CONTROL  FRONT RADAR SENSOR SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Front Radar Sensor / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Front Radar Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - - - Cannot be used
Total Distance Traveled - Unit - - - Cannot be used
Vehicle Setting Value Delta X - - - Cannot be used
Vehicle Setting Value Delta Z - - - Cannot be used
Vehicle Setting Value H - - - Cannot be used
Optical Axis Not Adjusted Status Beam axis not adjusted status Not Complete or Complete Not Complete: Beam axis adjustment not completed
Complete: Beam axis adjustment completed
If this item is "Not Complete", vehicle control history X2023 is stored.
Axis Adjustment Error Code Error code for axis alignment Normal/0 to 31 Error code applicable for beam axis alignment -
Optical Axis Adjustment Angle (Horizontal) (Latest) Latest beam axis adjustment angle value (horizontal) Min.: -12.8 deg, Max.: 12.7 deg Adjusted angle of beam axis alignment (Default value: 0.0 deg.) -
Optical Axis Adjustment Angle (Vertical) (Latest) Latest beam axis adjustment angle value (vertical) Min.: -12.8 deg, Max.: 12.7 deg Adjusted angle of beam axis alignment (Default value: 0.0 deg.) -
Optical Axis Adjustment Angle (Horizontal) (2nd Latest) 2nd latest beam axis adjustment angle value (horizontal) Min.: -12.8 deg, Max.: 12.7 deg Adjusted angle of beam axis alignment (Default value: 0.0 deg.) -
Optical Axis Adjustment Angle (Vertical) (2nd Latest) 2nd latest beam axis adjustment angle value (vertical) Min.: -12.8 deg, Max.: 12.7 deg Adjusted angle of beam axis alignment (Default value: 0.0 deg.) -
Optical Axis Offset Angle (Horizontal) Beam axis offset value (horizontal) Min.: -12.8 deg, Max.: 12.7 deg Beam axis offset value -
Optical Axis Offset Angle (Vertical) Beam axis offset value (vertical) Min.: -12.8 deg, Max.: 12.7 deg Beam axis offset value -
Optical Axis Offset Angle (Horizontal) (with On-Line Calibration Angle) Beam axis offset value (horizontal) (after completing calibration) Min.: -12.8 deg, Max.: 12.7 deg Beam axis offset value -
Optical Axis Offset Angle (Vertical) (with On-Line Calibration Angle) Beam axis offset value (vertical) (after completing calibration) Min.: -12.8 deg, Max.: 12.7 deg Beam axis offset value -
Microwave Integrated Circuit to Antenna in Front Radar Sensor Communication Error Communication malfunction status of millimeter wave radar sensor assembly antenna OFF or ON ON: Malfunction
OFF: Normal
If this item is "Malfunction", DTC C1A8887 is stored.
Antenna to Microwave Integrated Circuit in Front Radar Sensor Communication Error Communication malfunction status of microwave integrated circuit in millimeter wave radar sensor assembly OFF or ON ON: Malfunction
OFF: Normal
If this item is "Malfunction", DTC C1A8987 is stored.
Microwave Integrated Circuit (VCO Circuit) in Front Radar Sensor Internal Electronic Failure Internal malfunction status of microwave integrated circuit (VCO circuit) in millimeter wave radar sensor assembly OFF or ON ON: Malfunction
OFF: Normal
If this item is "Malfunction", DTC C1A8749 is stored.
Main Microcomputer in Front Radar Sensor Communication Error Communication malfunction status of main microcomputer in millimeter wave radar sensor assembly OFF or ON ON: Malfunction
OFF: Normal
If this item is "Malfunction", DTC C1A8C08 is stored.
IG Voltage Protection IG voltage protection status OFF or ON ON: Malfunction detected
OFF: Normal
If this item is "Malfunction Detected", vehicle control history X2028 is stored.
Optical Axis Misalignment (Horizontal) Beam axis misalignment (horizontal) result OFF or ON ON: Misalignment
OFF: Normal
-
Optical Axis Misalignment (Vertical) Beam axis misalignment (vertical) result OFF or ON ON: Misalignment
OFF: Normal
-
Millimeter-wave Circuit Temperature Protection Millimeter-wave circuit temperature protection status OFF or ON ON: Malfunction
OFF: Normal
If this item is "Malfunction Detected", vehicle control history X2027 is stored.
Destination Malfunction Destination malfunction status OFF or ON ON: Malfunction
OFF: Normal
-
IG Voltage IG voltage value Min.: 0 V, Max.: 25.5 V 11.0 to 14.0 V: Ignition switch ON -
Front Radar Sensor Temperature Temperature of area around millimeter wave radar sensor assembly Min.: -32768°C, Max.: 32767°C Actual temperature of area around millimeter wave radar sensor displayed This value differs to the outside temperature.
Vehicle Speed Vehicle speed Min.: -30 km/h (-19 mph), Max.: 225.99 km/h (159 mph) Almost same as actual vehicle speed -
PCS Destination Variation No Variation number of PCS destination 0 to 15 Displays PCS destination number -
Radar Cruise Control System Destination Variation No Variation number of radar cruise control system destination 0 to 15 Displays the radar cruise control system destination number -
TMN Destination Variation No Variation number of Traffic Movement Notification destination 0 to 15 Displays TMN destination number -
Front Radar Sensor Destination Variation No Millimeter wave radar sensor assembly destination number 0 to 15 Displays the millimeter wave radar sensor assembly destination number -
Acceleration Suppression at Low Speed Destination Variation No Variation number of acceleration suppression at low speed destination 0 to 15 Displays the acceleration suppression at low speed destination number -
Ambient Temperature Temperature of outside air around the vehicle MIN: -78.75°C, MAX: 78.125°C Displays ambient temperature -
Wiper Operation Status Operating status of windshield wiper Front Wiper Stop / Front Wiper INT / Front Wiper LO / Front Wiper HI / Front Wiper Storage / Service Position / Front Wiper Malfunction Displays operating status of front wiper -
On-Line Calibration Angle (Horizontal) Calibrated angle value (horizontal) Min.: -12.8 deg, Max.: 12.7 deg Learned value -
On-Line Calibration Angle (Vertical) Calibrated angle value (vertical) Min.: -12.8 deg, Max.: 12.7 deg Learned value -