Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2020.08
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0303031 AUTOMATIC HIGH BEAM SYSTEM U

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Auto high beam switch signal ON or OFF ON: Auto high beam switch pressed
OFF: Auto high beam switch not pressed
-
Dimmer SW Dimmer switch high position signal ON or OFF ON: Dimmer switch in high or high flash position
OFF: Dimmer switch in low position
-
Auto Light SW Light control switch AUTO position signal ON or OFF ON: Light control switch in AUTO position
OFF: Light control switch not in AUTO position
-
Head Light SW (Head) Light control switch head position signal ON or OFF ON: Light control switch in head position
OFF: Light control switch not in head position
-
Light Sensor Illuminance Light control sensor illuminance 0 to 8191 lx Value is output according to ambient light levels -
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 Undetec: Undetected
CAM NA: Camera detection malfunction*1
No sens: No detection
Hlight: Oncoming vehicles with headlights on
Taillgt: Preceding vehicles with taillights on
Speed: Vehicle speed
Daytime: Daytime state
Village: Urban area
Malfunc: System delay
Auto H Beam STS1 Automatic high beam sensor state past 1 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
Auto H Beam STS2 Automatic high beam sensor state past 2 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
Auto H Beam STS3 Automatic high beam sensor state past 3 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
Auto H Beam STS4 Automatic high beam sensor state past 4 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
Auto H Beam STS5 Automatic high beam sensor state past 5 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
Auto H Beam STS6 Automatic high beam sensor state past 6 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
Auto H Beam STS7 Automatic high beam sensor state past 7 Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc Condition can be displayed*3 *2
The Number of DTC Number of trouble codes 0 to 255 Condition can be displayed -

*1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.

*2: Although the item is displayed on the GTS, it is not applicable to the vehicle.


HINT:

*3: The details of each value of the Control Range are as follows:

Range Condition Control Condition Diagnostic Note
Undetec Automatic high beam sensor being initialized Control suspended (low beam headlights illuminated) -
CAM NA Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc. Control suspended (low beam headlights illuminated) -
No sens No lights detected High beam headlights illuminated Only when vehicle speed within operation speed range
Hlight Headlights of oncoming vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
Taillgt Taillights preceding vehicle, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
Speed No lights detected and vehicle speed below operation speed Low beam headlights illuminated -
Daytime Bright light detected Low beam headlights illuminated -
Village Streetlights, etc. detected Low beam headlights illuminated Only when vehicle speed within operation speed range
Delay Changing between low beams and high beams Changing between low beams and high beams Only when vehicle speed within operation speed range
Malfunc Not applicable - -
Aim Lmt
SAE Mod
Undefin
LIN Err


Body Electrical > Front Recognition Camera (Front Lighting Control) > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Actual driven distance 0 to 16777215 Roughly the same as the actual driven distance w/ Toyota Safety Sense
Total Distance Traveled - Unit Actual driven distance unit km or mile Displays the current actual driven distance unit w/ Toyota Safety Sense
AHB/AHS Information Automatic high beam system or adaptive high beam system specification information Unknown, AHB or AHS Unknown: Specification not stored
AHB: w/ Automatic High Beam System
AHS: w/ Adaptive High Beam System
w/ Toyota Safety Sense
Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Recognition Camera High Temperature 2 Forward recognition camera condition Not High Temperature or High Temperature Not High Temperature: 65°C (149°F) or lower High Temperature: 65°C (149°F) or higher
·

If this item is "High Temperature", the automatic high beam system will be temporarily unavailable. If this does not improve even if the inside of the vehicle is left cooled for at least 10 minutes, the forward recognition camera may be malfunctioning.

HINT:

In summertime, the windshield glass may reach 100°C (212°F) or higher.


·

w/ Toyota Safety Sense




ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Indicator Automatic high beam indicator light OFF or ON -