Home › Vehicle Exterior › LIGHTING (EXT) › AUTOMATIC HIGH BEAM SYSTEM › from 2020.08
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0303031 AUTOMATIC HIGH BEAM SYSTEM J

LIGHTING (EXT)  AUTOMATIC HIGH BEAM SYSTEM  Automatic High Beam System does not Operate or Operation Indicator does not Illuminate  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera.

WIRING DIAGRAM

E438594E03
1.083,5.354 3,5.583 1.917,0.229 10 false : CAN Communication Line 0.385,4.104 2.302,4.333 1.917,0.229 10 false Forward Recognition Camera 0.375,2.74 2.292,2.969 1.917,0.229 10 false Combination Meter Assembly 2.333,1.677 4.25,1.906 1.917,0.229 10 false Auto High Beam Switch 2.344,1.531 2.781,1.802 0.438,0.271 10 false F6 1.99,1.021 2.427,1.292 0.438,0.271 10 false 3 4.063,1.021 4.5,1.292 0.438,0.271 10 false 6 5.167,0.99 5.604,1.26 0.438,0.271 10 false 17 5.438,1 5.875,1.271 0.438,0.271 10 false AHBI 5.979,0.708 6.302,0.938 0.323,0.229 10 false +B 5.135,4.115 5.573,4.385 0.438,0.271 10 false F15 5.135,4.26 6.771,4.729 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

One time recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT

*1: w/ Entry and Start System




PROCEDURE

1.READ VALUE USING GTS
a.

Enter the following menus: Chassis / Front Recognition Camera / Data List.


b.

Read the Data List according to the display on the GTS.

Chassis > Front Recognition Camera > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Front Recognition Camera High Temperature 2 Forward recognition camera condition Not High Temperature or High Temperature Not High Temperature: 65°C (149°F) or lower
High Temperature: 65°C (149°F) or higher
If this item is "High Temperature", the automatic high beam system will be temporarily unavailable. If this does not improve even if the inside of the vehicle is left cooled for at least 10 minutes, the forward recognition camera may be malfunctioning.
HINT:

In summertime, the windshield glass may reach 100°C (212°F) or higher


Chassis > Front Recognition Camera > Data List
Tester Display
Front Recognition Camera High Temperature 2
50003 430 13
OK:

"Not High Temperature" is displayed on the GTS.


HINT:

If "High Temperature" is displayed, move the vehicle to a cool place and allow the temperature of the forward recognition camera to decrease before continuing with troubleshooting.



Result:
Proceed to
OK
NG



OK

2.CHECK AUTOMATIC HIGH BEAM INDICATOR LIGHT

NG

END (THE SYSTEM STOPPED OPERATING DUE TO HIGH TEMPERATURES)

2.CHECK AUTOMATIC HIGH BEAM INDICATOR LIGHT
a.

Check the operation of the automatic high beam indicator light.

i.

Turn the ignition switch to ON.


ii.

Turn the light control switch to the AUTO or HEAD position.


iii.

Cover the automatic light control sensor to turn the low beam headlights on.


iv.

Move the dimmer switch to the high position.


v.

Press the auto high beam switch.



Result:
Result Proceed to
OK (The automatic high beam indicator light and the auto high beam switch indicator illuminate) A
NG (Automatic high beam indicator light does not illuminate) B
NG (Automatic high beam indicator light and auto high beam switch indicator do not operate) C



A

3.READ VALUE USING GTS

B

5.PERFORM ACTIVE TEST USING GTS

C

6.READ VALUE USING GTS
3.READ VALUE USING GTS
E367861C01
0.427,0.74 0.625,0.74 0.625,0.74 0.927,0.906 true 2.167,1.281 2.5,1.833 2.5,1.833 2.74,1.833 true 0.25,0.667 0.563,0.865 0.313,0.198 10 false *2 2.792,1.74 3.104,1.938 0.313,0.198 10 false *1 1.49,1.198 1.802,1.396 0.313,0.198 10 false *a
*1 Forward Recognition Camera
(Automatic High Beam Sensor)
*2 Work Light or Equivalent
*a 100 mm or less


a.

Shine a light on the automatic high beam sensor (forward recognition camera).

HINT:

If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.



b.

Enter the following menus: Body Electrical / Main Body / Data List.


c.

Read the Data List according to the display on the GTS.

HINT:

As it may take time for the values in the Data List to change, wait at least 10 seconds before reading the Data List.


Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed Undetec: Undetected
CAM NA: Camera detection malfunction*1
No sens: No detection
Hlight: Oncoming vehicles with headlights on
Taillgt: Preceding vehicles with taillights on
Speed: Vehicle speed
Daytime: Daytime state
Village: Urban area
Malfunc: System delay

*1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.


Body Electrical > Main Body > Data List
Tester Display
Auto H Beam STS0
50003 123 169
OK:

"Daytime" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS

NG

REPLACE FORWARD RECOGNITION CAMERA

4.READ VALUE USING GTS
E367862C01
1.667,1.229 1.917,1.771 1.917,1.771 2.094,1.771 true 1,0.854 1.313,1.052 0.313,0.198 10 false *a 0.969,1.51 1.281,1.708 0.313,0.198 10 false *a 2.365,0.875 2.677,1.073 0.313,0.198 10 false *b 2.146,1.688 2.458,1.885 0.313,0.198 10 false *1
*1 Cardboard or Equivalent Object
*a 150 mm or more
*b 3 mm or more


a.

Cover the automatic high beam sensor with an opaque object, such as cardboard.

NOTICE:
·

Make sure that there is no clearance between the cardboard or equivalent object and the area of the windshield glass in front of the automatic high beam sensor.

·

If there is any clearance, light may shine on the automatic high beam sensor and the value of the Data List will not change.




b.

Enter the following menus: Body Electrical / Main Body / Data List.


c.

Read the Data List according to the display on the GTS.

HINT:

As it may take time for the values in the Data List to change, wait at least 10 seconds before reading the Data List.


Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Automatic High Beam Headlights Sensor Detection Status Automatic high beam sensor current state Undetected, N/A, No sens, Headlight, Taillight, Speed, Daytime, Village, Other sens, Change, Out of aim, SAE Mod, Aim adjust or LIN Err Condition can be displayed -
Body Electrical > Main Body > Data List
Tester Display
Automatic High Beam Headlights Sensor Detection Status
50003 449 119
OK:

"Speed" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

NG

REPLACE FORWARD RECOGNITION CAMERA

5.PERFORM ACTIVE TEST USING GTS
a.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Indicator Automatic high beam indicator light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Automatic High Beam Indicator
50004 122 104
OK:

The automatic high beam indicator illuminates and turns off.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

6.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical / Main Body / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto High Beam Main Switch Auto high beam switch signal OFF or ON OFF: Auto high beam switch not pressed
ON: Auto high beam switch pressed
-
Body Electrical > Main Body > Data List
Tester Display
Auto High Beam Main Switch
50003 449 107
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS

NG

9.INSPECT AUTO HIGH BEAM SWITCH
7.READ VALUE USING GTS
a.

Enter the following menus: Body Electrical / Main Body / Data List.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto H Beam STS0 Automatic high beam sensor current state Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin or LIN Err Condition can be displayed Undetec: Undetected
CAM NA: Camera detection malfunction*1
No sens: No detection
Hlight: Oncoming vehicles with headlights on
Taillgt: Precedin gvehicles with taillights on
Speed: Vehicle speed
Daytime: Daytime state
Village: Urban area
Malfunc: System delay

*1: If CAM NA is displayed, the forward recognition camera may have stopped operating due to high temperature.


Body Electrical > Main Body > Data List
Tester Display
Auto H Beam STS0
50003 123 169
OK:

"Daytime" or "Speed" is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

8.PERFORM ACTIVE TEST USING GTS

NG

REPLACE FORWARD RECOGNITION CAMERA

8.PERFORM ACTIVE TEST USING GTS
a.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


b.

Perform the Active Test according to the display on the GTS.

OK:

The automatic high beam indicator illuminates and turns off.


Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Automatic High Beam Indicator Automatic high beam indicator light OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Automatic High Beam Indicator
50004 122 104

Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

9.INSPECT AUTO HIGH BEAM SWITCH

OK

10.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)

NG

10.CHECK HARNESS AND CONNECTOR (AUTO HIGH BEAM SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND BODY GROUND)
a.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F6-6 (+B) - F15-17 (AHBI) Always Below 1 Ω
F6-6 (+B) or F15-17 (AHBI) - Body ground Always 10 kΩ or higher
F6-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR