Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for LHD) › from 2020.08
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0298588 BRAKE ACTUATOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of brake actuator assembly Operate the electric parking brake switch assembly Parking brake indicator light (red) blinks when the ignition switch is first turned on (IG) (Click here)
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION / NOTICE / HINT

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55736D 5.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 6.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 7.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 28800 8.REMOVE BATTERY

Hide 9.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 10.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C368538C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C369564C01
1.49,1.854 1.708,1.708 true 2.156,1.313 2.479,1.26 true 0.958,1.479 1.302,1.479 true 0.979,1.167 1.542,1.313 true 1.844,1.094 2.469,0.948 true 2.042,0.927 2.469,0.677 true 1.25,1.781 1.458,2 0.208,0.219 10 true *a 2.521,1.146 2.75,1.365 0.229,0.219 10 true *b 0.75,1.396 0.927,1.594 0.177,0.198 10 true *c 0.698,1.073 0.938,1.292 0.24,0.219 10 true *d 2.5,0.844 2.729,1.052 0.229,0.208 10 true *e 2.521,0.573 2.74,0.76 0.219,0.188 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Use tags or make a memo to identify the places to reconnect the brake tubes.


c.
C368539

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


d.
C368540

Remove the bolt, 2 nuts and brake actuator with bracket from the vehicle.

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not hold the brake actuator assembly by the connector.



HINT:

Remove the brake actuator with bracket while avoiding the brake tubes.



Hide 44510 11.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C366937

Loosen the 2 nuts.


b.

Remove the bolt and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44521A 12.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C366938

Remove the No. 1 brake actuator case collar from the brake actuator bracket cushion.


Hide 44547B 13.REMOVE BRAKE ACTUATOR BRACKET CUSHION

C366939

a.

Remove the brake actuator bracket cushion from the brake actuator bracket assembly.