Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for LHD) › from 2020.08
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0298577 BRAKE MASTER CYLINDER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the brake master cylinder sub-assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the master cylinder sub-assembly from the brake booster assembly.


CAUTION / NOTICE / HINT

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 2.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55736D 3.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 4.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 28800 6.REMOVE BATTERY

Hide 7.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 31434 8.DISCONNECT CLUTCH RESERVOIR TUBE (for Manual Transaxle)

a.

Slide the clip and disconnect the clutch reservoir tube from the brake master cylinder sub-assembly.


Hide 47201 9.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

a.
C366063

Disengage the clamp and disconnect the reservoir level switch connector.


b.
C366064

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

NOTICE:
·

Do not damage or deform the brake lines during the removal procedure.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




c.
C366870

Using a 13 mm deep socket wrench, remove the nut and separate the wire harness bracket.


d.

Using a 13 mm deep socket wrench, remove the nut and brake master cylinder sub-assembly from the brake booster assembly.

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its brake master cylinder reservoir assembly when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of cloth and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other type of grease or fluid.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.




e.

Remove the brake master cylinder O-ring from the brake master cylinder sub-assembly.