Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1589  Acceleration Sensor Learning Value  


DESCRIPTION

The ECM stores DTC P1589 if deceleration sensor zero point calibration is not performed or failed after system components such as the ECM are replaced.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1589 Acceleration Sensor Learning Value Either one of the following conditions is met (1 trip detection logic):
·

When the vehicle speed is 2 km/h (1.2 mph) or more, Deceleration Sensor Zero Point Calibration has not been completed.

·

While Deceleration Sensor Zero Point Calibration is performed, the learned values of Deceleration Sensor Zero Point Calibration are abnormal (out of normal range).


·

Deceleration Sensor Zero Point Calibration has not been performed.

·

Vehicle was not stable during Deceleration Sensor Zero Point Calibration.

·

Airbag sensor assembly (Yaw rate and acceleration sensor)

·

ECM


Does not come on DTC stored

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition The vehicle speed is 2 km/h (1.2 mph) or more. ○ -
Deceleration Sensor Zero Point Calibration is performed. - ○
Malfunction Condition Deceleration Sensor Zero Point Calibration has not been completed. ○ -
The learned values of Deceleration Sensor Zero Point Calibration are abnormal (out of normal range). - ○
Duration - -
Detection Logic 1 trip detection logic 1 trip detection logic

HINT:

This DTC is output when either of the above detection patterns is met.


CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle 2 km/h (1 mph) or more.



PROCEDURE

1.PERFORM INITIALIZATION (DECELERATION SENSOR ZERO POINT CALIBRATION)
NOTICE:
·

If CVT oil pressure calibration is performed before deceleration sensor zero point calibration, DTC P1589 is stored. In this case, perform steps *1, *2, *3, *4 and *5 to return the system to normal.

·

Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).

·

Do not shake or vibrate the vehicle during calibration.



a.

Turn the ignition switch off.*1


b.

Move the shift lever to P and apply the parking brake.*2


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.*3

NOTICE:

Do not start the engine.



e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Reset Memory.*4

Powertrain > Engine and ECT > Utility
Tester Display
Reset Memory
50005 234 176

f.

Enter the following menus: Powertrain / ECT / Utility / Deceleration Sensor Zero Point Calibration.*5

Powertrain > Engine and ECT > Utility
Tester Display
Deceleration Sensor Zero Point Calibration
50005 234 2123
HINT:
·

When "Complete" is displayed on the screen, deceleration sensor zero point calibration is complete.

·

If "Error" is displayed on the screen, the deceleration sensor circuit may be malfunctioning.

·

Shaking or vibrating the vehicle during deceleration sensor zero point calibration may cancel calibration. If "Error" is displayed on the screen, perform step *5 again.




g.

If "Error" is displayed on the GTS, read the DTCs using the GTS.

Result:
Result Proceed to
Deceleration sensor zero point calibration is completed normally A
DTC P1589 is output B




A

2.PERFORM CVT OIL PRESSURE CALIBRATION

B

3.CHECK AIRBAG SENSOR ASSEMBLY
2.PERFORM CVT OIL PRESSURE CALIBRATION
NOTICE:

Do not clear the learned values by performing Reset Memory.


a.

Turn the ignition switch off and wait at least 30 seconds.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait at least 2 seconds.

NOTICE:

Do not start the engine.


HINT:

CVT oil pressure calibration is performed with the ignition switch ON (engine stopped). However, calibration cannot be performed under the following conditions:

·

Oil pressure sensor value is 0.065 MPa (0.663 kgf/cm2, 9.43 psi) or higher.

·

CVT oil temperature is -5°C (23°F) or less or 120°C (248°F) or higher.




d.

Enter the following menus: Powertrain / Engine and ECT / Utility.


e.

Start the engine and wait at least 5 seconds.

NOTICE:
·

Start the engine with the shift lever in P.

·

After starting the engine, do not operate the accelerator pedal.




f.

Enter the following menus: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.

HINT:
·

During CVT oil pressure calibration, the engine idle speed will increase.

·

When "Complete" is displayed on the screen, CVT oil pressure calibration is complete.

·

The learned values cannot be cleared by only disconnecting and reconnecting the cable to the negative (-) battery terminal.



Powertrain > Engine and ECT > Utility
Tester Display
CVT Oil Pressure Calibration
50005 234 2122

g.

Check for DTCs again.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Proceed to
NEXT



NEXT

END

3.CHECK AIRBAG SENSOR ASSEMBLY
a.

Check the airbag sensor assembly (yaw rate and acceleration sensor) for any inclination, bracket deformation or installation clearance.

OK:

The airbag sensor assembly (yaw rate and acceleration sensor) is installed correctly.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (G SENSOR)

NG

4.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of yaw rate and acceleration sensor Min.: 0 V
Max.: 79.998 V
Displays converted voltage of yaw rate and acceleration sensor
·

2.31 V to 2.69 V: Vehicle on level ground

·

1.88 V to 2.5 V: Decelerating

·

2.5 V to 3.11 V: Accelerating

·

Set to 1.87 V: G sensor malfunction

·

Set to 1.87 V: Communication malfunction


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

5.REPLACE ECM

B

6.REPLACE AIRBAG SENSOR ASSEMBLY
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Replace the airbag sensor assembly (yaw rate and acceleration sensor).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT