Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to change the shift range between M1 and M7 using the transmission control switch. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C342245E20
1.76,0.469 1.917,0.667 0.156,0.198 10 false 4 2,0.469 2.313,0.667 0.313,0.198 10 false IG 3.177,0.469 3.333,0.667 0.156,0.198 10 false S 3.427,0.469 3.583,0.667 0.156,0.198 10 false 5 3.427,1.135 3.802,1.354 0.375,0.219 10 false 1 3.427,1.833 3.74,2.031 0.313,0.198 10 false 3 2.958,1.833 3.5,2.052 0.542,0.219 10 false SFTD 2.958,1.177 3.573,1.375 0.615,0.198 10 false SFTU 2.01,1.823 2.167,2.021 0.156,0.198 10 false E 1.76,1.833 1.917,2.031 0.156,0.198 10 false 2 4.938,0.469 5.25,0.667 0.313,0.198 10 false 59 4.938,1.167 5.25,1.365 0.313,0.198 10 false 42 4.938,1.865 5.25,2.063 0.313,0.198 10 false 43 5.219,1.885 5.833,2.083 0.615,0.198 10 false SFTD 5.219,1.167 5.833,1.365 0.615,0.198 10 false SFTU 5.25,0.49 5.406,0.688 0.156,0.198 10 false S 6.167,0.969 6.781,1.167 0.615,0.198 10 false 12 V 6.167,1.667 6.781,1.865 0.615,0.198 10 false 12 V 5.708,2.5 6.167,2.698 0.458,0.198 10 false A38 5.708,2.667 6.167,2.865 0.458,0.198 10 false ECM 1.583,2.417 2.042,2.615 0.458,0.198 10 false F17 1.583,2.615 3.615,3.417 2.031,0.802 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 0.25,0.51 1.135,1.083 0.885,0.573 10 false from ECU-IG1 NO. 1 Fuse

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

B

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport mode select switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

3.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

8.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status OFF or ON
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sports Shift Down SW Sport shift down switch status OFF or ON
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Shift Up SW
Sports Shift Down SW
50003 234 134,135

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C277025C67
1.875,1.781 2.01,1.385 true 2.552,1.76 2.292,1.396 true 1.26,1.76 1.729,1.385 true 2.427,1.833 2.927,2.031 0.5,0.198 10 false SFTD 1.844,1.823 2.156,2.021 0.313,0.198 10 false E 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.042,1.823 1.521,2.021 0.479,0.198 10 false SFTU
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
3 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
1 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - BODY GROUND)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - BODY GROUND)
a.
C245154C45
0.438,1 0.865,1.292 0.427,0.292 1.208,1.667 1.365,1.667 1.365,1.667 1.573,1.292 true 0.313,0.302 0.625,0.5 0.313,0.198 10 false *a 0.542,1.073 1,1.271 0.458,0.198 10 false F17 1.031,1.594 1.344,1.792 0.313,0.198 10 false E
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F17-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.
C277060C50
1.531,0.167 1.896,0.427 0.365,0.26 2.792,1.833 2.313,1.167 true 1.771,1.802 2.229,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.604,0.208 1.917,0.406 0.313,0.198 10 false A38 2.594,1.896 3.365,2.115 0.771,0.219 10 false 43 (SFTD) 1.438,1.896 2.208,2.115 0.771,0.219 10 false 42 (SFTU)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-43 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
A38-43 (SFTD) - Body ground Shift lever in M 10 kΩ or higher
A38-42 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
A38-42 (SFTU) - Body ground Shift lever in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C277025C68
1.156,1.354 0.75,1.75 true 1.563,1.323 2,1.75 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 0.635,1.76 0.792,1.958 0.156,0.198 10 false S 2.073,1.76 2.385,1.958 0.313,0.198 10 false IG
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) POWER SOURCE)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

9.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) POWER SOURCE)
a.
C245154C46
0.438,1 0.865,1.292 0.427,0.292 2.229,1.667 2.01,1.667 2.01,1.667 1.865,1.302 true 0.313,0.302 0.625,0.5 0.313,0.198 10 false *a 0.542,1.073 1,1.271 0.458,0.198 10 false F17 2.292,1.604 2.604,1.802 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly (transmission control switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F17-4 (IG) - Body ground Ignition switch ON 11 to 14 V
F17-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

CHECK POWER SOURCE CIRCUIT (TRANSMISSION CONTROL SWITCH)

10.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-5 (S) - A38-59 (S) Always Below 1 Ω
F17-5 (S) - Body ground and other terminals Always 10 kΩ or higher
A38-59 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT