Home › Drivetrain › CLUTCH › CLUTCH UNIT (for EC6A) › from 2020.08
RM32H0E _52 Drivetrain _059611 CLUTCH _0292334 CLUTCH UNIT(for EC6A) A

CLUTCH  CLUTCH UNIT(for EC6A)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the clutch unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Front wheel alignment adjustment
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 31483E 2.REMOVE BLEEDER CLUTCH RELEASE TUBE

a.
C368005

Remove the 2 bolts and bleeder clutch release tube from the manual transaxle assembly.


b.

Using a 10 mm union nut wrench, separate the bleeder clutch release tube from the clutch release bleeder sub-assembly.


Hide 31407B 3.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

C357046

a.

Using a 10 mm union nut wrench, separate the clutch release bleeder sub-assembly from the clutch release cylinder to flexible hose tube.


b.

Remove the 2 bolts and clutch release bleeder sub-assembly from the manual transaxle assembly.


Hide 31400 4.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C357764

Remove the clutch tube boot from the manual transaxle assembly.


b.
C357047

Remove the 3 bolts and clutch release cylinder with bearing assembly together with clutch release cylinder to bleeder tube from the manual transaxle assembly.


Hide 31483 5.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

a.
C187782

Using a 10 mm union nut wrench, remove the clutch release cylinder to flexible hose tube from the clutch release cylinder with bearing assembly.


Hide 31210 6.REMOVE CLUTCH COVER ASSEMBLY

C283237C01
1.125,0.75 0.792,0.865 0.792,0.865 1.063,0.708 true 0.635,0.76 0.948,0.917 0.313,0.156 10 false *a
*a Matchmarks


a.

Put matchmarks on the clutch cover assembly and the flywheel sub-assembly.


b.

Loosen each bolt 180° at a time until the spring tension is released.


c.

Remove the 6 bolts and pull off the clutch cover assembly.

NOTICE:

Do not drop the clutch disc assembly.



Hide 31250 7.REMOVE CLUTCH DISC ASSEMBLY

NOTICE:

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.