Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/ Entry and Start System) › from 2021.09
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299015 IMMOBILISER SYSTEM(w/ Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


B271001E31
3.354,0.229 3.729,0.458 0.375,0.229 3.427,0.26 3.74,0.438 0.313,0.177 10 false F59

a.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F59-6 (AGND) - Body ground - P - Body ground Transponder key amplifier ground Always Below 1 Ω -
F59-7 (TXCT) - F59-6 (AGND) Input B - P Immobiliser communication input Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
F59-8 (CODE) - F59-6 (AGND) Output L - P Immobiliser communication output Engine switch off,brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -
F59-10 (VC5) - F59-6 (AGND) Input Y - P Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V -

*1: for CVT

*2: for Manual Transaxle



b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F59-7 (TXCT) - F59-6 (AGND) Input B - P Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



F59-8 (CODE) - F59-6 (AGND) Output L - P Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch* Pulse generation
(See waveform 2)
F59-10 (VC5) - F59-6 (AGND) Input Y - P Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 3)

HINT:

*: Remove the transmitter battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F59-7 (TXCT) - F59-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed


ii.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F59-8 (CODE) - F59-6 (AGND)
Tool Setting
·

Waveform

1 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F59-10 (VC5) - F59-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B416786E08
4.563,0.563 4.938,0.802 0.375,0.24 4.656,0.594 4.969,0.792 0.313,0.198 10 false F1

a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F1-4 (+B) - F1-18 (E) Input L - W-B +B power supply Always 11 to 14 V -
F1-18 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F1-17 (IG1D) - F1-18 (E) Output GR - W-B Ignition power supply Engine switch off Below 1 V -
Engine switch on (IG) 11 to 14 V -
F1-5 (TXCT) - F1-11 (AGND) Output B - P Signal output to transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F1-6 (CODE) - F1-11 (AGND) Input L - P Signal input from transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
F1-7 (VC5) - F1-11 (AGND) Output Y - P Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more after driver door opened and then closed Below 1 V
F1-11 (AGND) - Body ground - P - Body ground Transponder key amplifier ground Always Below 1 Ω
F1-20 (IND) - F1-18 (E) Output P - W-B Security indicator output Engine switch off → on (IG) Pulse generation → Below 2 V -

*1: for CVT

*2: for Manual Transaxle



e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F1-5 (TXCT) - F1-11 (AGND) Output B - P Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F1-6 (CODE) - F1-11 (AGND) Input L - P Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch
HINT:

Remove the transmitter battery before performing this inspection.


Pulse generation
(See waveform 2)
F1-7 (VC5) - F1-11 (AGND) Output Y - P Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 3)


f.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F1-5 (TXCT) - F1-11 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed


ii.
B368716C01
0.104,0.135 0.417,0.292 0.313,0.156 10 false *a 0.094,1.896 0.406,2.052 0.313,0.156 10 false *b 3.031,1.219 3.427,1.49 0.396,0.271 10 false GND 3.031,2.948 3.427,3.219 0.396,0.271 10 false GND
*a Waveform
*b Waveform (detail)


Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F1-6 (CODE) - F1-11 (AGND)
Tool Setting
·

Waveform

1 V/DIV., 20 ms./DIV.

·

Waveform (detail)

2 V/DIV., 100 μs./DIV.


Condition Engine switch off, engine switch pressed with electrical key transmitter sub-assembly held near engine switch*

HINT:

*: Remove the transmitter battery before performing this inspection.



iii.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F1-7 (VC5) - F1-11 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed




CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B278917E31
3.396,0.156 3.792,0.385 0.396,0.229 3.458,0.188 3.781,0.365 0.323,0.177 10 false F21

a.

Disconnect the F21 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F21-1 (+B) - Body ground Input W - Body ground +B power supply Always 11 to 14 V B2789
F21-5 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω B2789


c.

Reconnect the F21 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F21-3 (EFII) - F21-5 (GND) Input G - W-B EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Engine switch off 11 to 14 V
·

B279986*1

·

B2799*2

·

B279A12*1

·

B279A*2

·

EFI Code Receive

·

Engine Start Request


F21-4 (EFIO) - F21-5 (GND) Output R - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Engine switch off 11 to 14 V → Below 1 V
F21-3 (EFII) - F21-5 (GND) Input G - W-B EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
F21-4 (EFIO) - F21-5 (GND) Output R - W-B EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)

*1: for 8NR-FTS

*2: for 3ZR-FAE



e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection F21-3 (EFII) - F21-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection F21-4 (EFIO) - F21-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Engine switch turned on (IG) using registered electrical key transmitter sub-assembly




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


B118684C34
3.469,0.333 3.844,0.552 0.375,0.219 3.563,0.375 3.885,0.542 0.323,0.167 10 false F78

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F78-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F78-3 (IGE) - F78-1 (GND) Input P - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P*1

·

Steering unlocked

·

Engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


F78-4 (SLP1) - F78-1 (GND) Output G - W-B Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked* 11 to 14 V → Below 1.5 V Sensor Value
F78-6 (IG2) - F78-1 (GND) Input B - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off Below 1 V B2788
Engine switch on (IG) 11 to 14 V
F78-7 (B) - Body ground Input L - Body ground Constant power supply Always 11 to 14 V B2788

HINT:

*: The steering locks when any door is opened with the shift lever in P*1 and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).


*1: for CVT



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F78-3 (IGE) - F78-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P*1

·

Steering unlocked

·

Engine switch turned off



*1: for CVT





CHECK ECM (for 8NR-FTS)


A384862C12
2.417,0.344 2.917,0.594 0.5,0.25 5.323,0.75 5.833,1 0.51,0.25 2.417,0.75 2.917,1 0.5,0.25 2.531,0.396 2.99,0.594 0.458,0.198 10 false C62 5.427,0.802 5.885,1 0.458,0.198 10 false A38 2.542,0.813 3,1.01 0.458,0.198 10 false C74 3,0.396 3.458,0.594 0.458,0.198 10 false *A 3,0.813 3.458,1.01 0.458,0.198 10 false *B
*A for TMMT Made *B for TMC Made


a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

for TMMT Made:
Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C62-53 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A38-45 (IMO) - C62-53 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Engine switch off 11 to 14 V -
A38-45 (IMO) - C62-53 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
-
A38-28 (IMI) - C62-53 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Engine switch off 11 to 14 V → Below 1 V -
A38-28 (IMI) - C62-53 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
-

for TMC Made:
Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C74-53 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A38-45 (IMO) - C74-53 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Engine switch off 11 to 14 V -
A38-45 (IMO) - C74-53 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
-
A38-28 (IMI) - C74-53 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Engine switch off 11 to 14 V → Below 1 V -
A38-28 (IMI) - C74-53 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection
·

A38-45 (IMO) - C62-53 (E1)*1

·

A38-45 (IMO) - C74-53 (E1)*2


Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery

*1: for TMMT Made

*2: for TMC Made



ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection
·

A38-28 (IMI) - C62-53 (E1)*1

·

A38-28 (IMI) - C74-53 (E1)*2


Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Engine switch turned on (IG) using registered electrical key transmitter sub-assembly

*1: for TMMT Made

*2: for TMC Made





CHECK ECM (for 3ZR-FAE)


A384862E12
5.323,0.75 5.833,1 0.51,0.25 2.427,0.76 2.938,1.01 0.51,0.25 5.438,0.802 5.896,1 0.458,0.198 10 false A38 2.542,0.813 2.875,0.979 0.333,0.167 10 false C63

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
C63-59 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
A38-45 (IMO) - C63-59 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Engine switch off 11 to 14 V -
A38-45 (IMO) - C63-59 (E1) Output GR - W-B ID code box (immobiliser code ECU) communication output Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery Pulse generation
(See waveform 1)
-
A38-28 (IMI) - C63-59 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Engine switch off 11 to 14 V → Below 1 V -
A38-28 (IMI) - C63-59 (E1) Input BE - W-B ID code box (immobiliser code ECU) communication input Engine switch turned on (IG) using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A38-45 (IMO) - C63-59 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after cable disconnected and reconnected to battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A38-28 (IMI) - C63-59 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Engine switch turned on (IG) using registered electrical key transmitter sub-assembly