Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM U

8NR-FTS ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A384862C08
2.417,0.75 2.917,1 0.5,0.25 5.323,0.75 5.833,1 0.51,0.25 2.406,0.354 2.906,0.604 0.5,0.25 2.521,0.802 2.979,1 0.458,0.198 10 false C74 5.427,0.802 5.885,1 0.458,0.198 10 false A38 2.521,0.396 2.979,0.594 0.458,0.198 10 false C62 3.031,0.375 3.49,0.573 0.458,0.198 12 false *A 3.052,0.781 3.51,0.979 0.458,0.198 12 false *B
*A for TMMT Made *B for TMC Made


HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals is also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-1 (BATT) - C62*7, C74*8-53 (E1) B - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A38-2 (+B) - C62*7, C74*8-53 (E1) R - W-B Power source of ECM Ignition switch ON 11 to 14 V
A38-3 (+B2) - C62*7, C74*8-53 (E1) R - W-B Power source of ECM Ignition switch ON 11 to 14 V
A38-6 (IGSW) - C62*7, C74*8-53 (E1) BE - W-B Ignition switch signal Ignition switch ON 11 to 14 V
A38-8 (IREL) - C62*7, C74*8-53 (E1) L - W-B D INJ relay operation signal Engine stopped, ignition switch ON 0 to 1.5 V
A38-9 (STP) - C62*7, C74*8-53 (E1) R*7 - W-B
G*8 - W-B
Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A38-10 (ST1-) - C62*7, C74*8-53 (E1) G*7 - W-B
LG*8 - W-B
Stop light switch assembly signal (opposite to STP terminal) Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A38-11 (IWPI) - C62*7, C74*8-53 (E1) V - W-B Electric water pump assembly signal Electric water pump assembly operating Pulse generation
A38-13 (CANH) - C62*7, C74*8-53 (E1) R*8 - W-B
GR*7 - W-B
CAN communication signal Engine stopped, ignition switch ON Pulse generation
(See waveform 1)
A38-21 (FPC) - C62*7, C74*8-53 (E1) LG - W-B Fuel pump control signal Engine stopped, ignition switch ON Below 1.5 V
A38-24 (IWPO) - C62*7, C74*8-53 (E1) SB - W-B Electric water pump assembly signal Electric water pump assembly operating Pulse generation
A38-26 (CANL) - C62*7, C74*8-53 (E1) P - W-B CAN communication signal Engine stopped, ignition switch ON Pulse generation
(See waveform 2)
A38-29 (STA) - C62*7, C74*8-53 (E1) LG - W-B Starter operation signal Cranking 6.0 V or higher
A38-30 (NEO) - C62*7, C74*8-53 (E1) L - W-B Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 3)
A38-36 (MTMS)*10 - C62*7, C74*8-53 (E1) SB - W-B iMT switch signal Ignition switch ON and iMT switch pushed Below 1.5 V
Ignition switch ON and iMT switch not pushed 11 to 14 V
A38-44 (SPD) - C62*7, C74*8-53 (E1) V - W-B Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 5)
A38-46 (MREL) - C62*7, C74*8-53 (E1) G - W-B EFI-MAIN relay operation signal Engine stopped, ignition switch ON 11 to 14 V
A38-47 (VPA) - A38-48 (EPA) R*7 - L
SB*8 - L
Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A38-49 (VCPA) - A38-48 (EPA) Y - L Power source of accelerator pedal position sensor (for VPA) Engine stopped, ignition switch ON 4.5 to 5.5 V
A38-50 (VPA2) - A38-51 (EPA2) V*7 - W
LG*8 - W
Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
A38-52 (VCP2) - A38-51 (EPA2) G - W Power source of accelerator pedal position sensor (for VPA2) Engine stopped, ignition switch ON 4.5 to 5.5 V
A38-57 (NSW) - C62*7, C74*8-53 (E1) W - W-B Park/neutral position switch signal Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 3.0 V
A38-58 (KSW)*2 - C62*7, C74*8-53 (E1) Y*7, GR*8 - W-B Key unlock warning switch input signal Ignition switch off → ON 0 to 3.0 V
A38-58 (KSW)*3 - C62*7, C74*8-53 (E1) Y*7, GR*8 - W-B Key unlock warning switch input signal Key in ignition key cylinder Below 1 V
No key in ignition key cylinder 11 to 14 V or Pulse generation
A38-59 (S)*1 - C62*7, C74*8-53 (E1) W - W-B M shift position switch signal Ignition switch ON, shift lever in M 11 to 14 V
Ignition switch ON, shift lever not in M Below 1 V
A38-60 (RFC) - C62*7, C74*8-53 (E1) R - W-B Cooling fan control signal Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 6)
C62*7, C74*8-9 (OC1+) - C62*7, C74*8-8 (OC1-) L - G Cam timing oil control solenoid assembly (for intake camshaft) operation signal Idling Pulse generation
(See waveform 7)
C62*7, C74*8-16 (M+) - C62*7, C74*8-49 (ME01) V - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 8)
C62*7-17 (HT1B)*5 - C62*7, C74*8-53 (E1) W - W-B Heated oxygen sensor heater operation signal Engine stopped, ignition switch ON 11 to 14 V
Idling with cold engine Below 3.0 V
C62*7, C74*8-19 (HA1A) - C62*7, C74*8-18 (E04) W - W-B Air fuel ratio sensor (sensor 1) heater operation signal Engine stopped, ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 9)
C62*7, C74*8-21 (#2D+) - C62*7, C74*8-20 (#2D-) V - P No. 2 fuel injector assembly signal Idling with warm engine Pulse generation
C62*7, C74*8-22 (#3D+) - C62*7, C74*8-23 (#3D-) G - R No. 3 fuel injector assembly signal Idling with warm engine Pulse generation
C62*7, C74*8-25 (#4D+) - C62*7, C74*8-24 (#4D-) W - B No. 4 fuel injector assembly signal Idling with warm engine Pulse generation
C62*7, C74*8-26 (#1D+) - C62*7, C74*8-27 (#1D-) G - R No. 1 fuel injector assembly signal Idling with warm engine Pulse generation
C62*7, C74*8-28 (FP1+) - C62*7, C74*8-29 (FP1-) P - V Fuel pump (for high pressure side) signal Engine running Pulse generation
C62*7, C74*8-30 (+BD1) - C62*7, C74*8-53 (E1) G - W-B Power source of ECU (injector driver) Engine stopped, ignition switch ON 11 to 14 V
C62*7, C74*8-34 (D)*1 - C62*7, C74*8-53 (E1) Y - W-B D shift position switch signal D shift position switch signal 11 to 14 V
Ignition switch ON, shift lever not in D or M Below 1 V
C62*7, C74*8-35 (R)*1 - C62*7, C74*8-53 (E1) R - W-B R shift position switch signal Ignition switch ON, shift lever in R 11 to 14 V
Ignition switch ON, shift lever not in R Below 1 V
C62*7, C74*8-37 (WGV+) - C62*7, C74*8-36 (WGV-) B - Y Vacuum regulating valve assembly operation signal Vacuum regulating valve assembly operating Pulse generation
C62*7, C74*8-38 (OE1+) - C62*7, C74*8-68 (OE1-) G - P Cam timing oil control solenoid assembly (for exhaust camshaft) operation signal Idling Pulse generation
(See waveform 10)
C62*7, C74*8-39 (IGT4) - C62*7, C74*8-53 (E1) V - W-B No. 4 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 11)
C62*7, C74*8-40 (IGT3) - C62*7, C74*8-53 (E1) G - W-B No. 3 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 11)
C62*7, C74*8-41 (IGT2) - C62*7, C74*8-53 (E1) B - W-B No. 2 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 11)
C62*7, C74*8-42 (IGT1) - C62*7, C74*8-53 (E1) GR - W-B No. 1 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 11)
C62*7, C74*8-46 (M-) - C62*7, C74*8-49 (ME01) P - W-B Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(See waveform 12)
C62*7, C74*8-48 (+BM) - C62*7, C74*8-53 (E1) GR - W-B Power source of throttle actuator Always 11 to 14 V
C62*7, C74*8-52 (HA1B)*4, *6 - C62*7, C74*8-53 (E1) W - W-B Air fuel ratio sensor (sensor 2) heater operation signal Ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 13)
C62*7, C74*8-60 (+BD2) - C62*7, C74*8-53 (E1) R - W-B Power source of ECU (injector driver) Engine stopped, ignition switch ON 11 to 14 V
C62*7, C74*8-64 (P)*1, *4, *5 - C62*7, C74*8-53 (E1) B - W-B P shift position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
C62*7, C74*8-65 (P)*1, *6 - C62*7, C74*8-53 (E1) B - W-B P shift position switch signal Ignition switch ON, shift lever in P 11 to 14 V
Ignition switch ON, shift lever not in P Below 1 V
C62*7, C74*8-65 (N)*1, *4, *5 - C62*7, C74*8-53 (E1) L - W-B N shift position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V
C62*7, C74*8-66 (N)*1, *6 - C62*7, C74*8-53 (E1) L - W-B N shift position switch signal Ignition switch ON, shift lever in N 11 to 14 V
Ignition switch ON, shift lever not in N Below 1 V
C62*7, C74*8-67 (ABV) - C62*7, C74*8-53 (E1) BR - W-B Air by-pass valve operation signal Engine stopped, ignition switch ON 11 to 14 V
Air by-pass valve operating 1.5 V or less
C62*7, C74*8-69 (EOJV) - C62*7, C74*8-53 (E1) LG - W-B Oil pressure switching valve assembly operation signal Oil pressure switching valve assembly operating 1.5 V or less
Oil pressure switching valve assembly not operating 11 to 14 V
C62*7, C74*8-70 (PRG) - C62*7, C74*8-53 (E1) L - W-B Purge VSV operation signal Engine stopped, ignition switch ON 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 14)
C62*7, C74*8-76 (NE+) - C62*7, C74*8-109 (NE-) R - Y Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 15)
C62*7, C74*8-78 (PEX)*6 - C62*7, C74*8-79 (EPEX)*6 R - B Differential pressure sensor signal Ignition switch ON 0.4 to 4.8 V
C62*7, C74*8-80 (VC)*6 - C62*7, C74*8-79 (EPEX)*6 L - B Power source of differential pressure sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-81 (EV1+) - C62*7, C74*8-112 (EV1-) G - B Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 16)
C62*7, C74*8-82 (VV1+) - C62*7, C74*8-114 (VV1-) W - P Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 16)
C62*7, C74*8-88 (VTA2) - C62*7, C74*8-120 (ETA) B - G Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Engine running, accelerator pedal fully depressed 4.6 to 5.0 V
C62*7, C74*8-89 (VCCL)*10 - C62*7, C74*8-53 (E1) R - W-B Power supply for clutch stroke sensor Ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-92 (VG) - C62*7, C74*8-91 (E2G) G - L Mass air flow meter signal Idling, shift lever in P or N (neutral), A/C off 0.5 to 3.0 V
C62*7, C74*8-94 (THA) - C62*7, C74*8-93 (ETHA) V - GR Intake air temperature sensor (Mass air flow meter) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
C62*7, C74*8-97 (THEO) - C62*7, C74*8-96 (ETHE) BR - L Engine oil temperature sensor signal Idling with warm engine 0 to 5.0 V
C62*7, C74*8-98 (PEO) - C62*7, C74*8-129 (EPEO) W - SB Oil pressure sender gauge assembly signal Idling with warm engine 0.5 to 4.5 V
C62*7, C74*8-99 (A1B+)*4 - C62*7, C74*8-53 (E1) W - W-B Air fuel ratio sensor (sensor 2) signal Ignition switch ON 1.53 to 5.96 V
C62*7-99 (OX1B)*5 - C62*7-100 (EX1B)*5 W - B Heated oxygen sensor signal Engine speed maintained at 2500 rpm for 2 minutes after warming up engine Pulse generation
(See waveform 17)
C62*7, C74*8-100 (A1B-)*4 - C62*7, C74*8-53 (E1) B - W-B Air fuel ratio sensor (sensor 2) signal Ignition switch ON 1.17 to 4.49 V
C62*7, C74*8-101 (IGF1) - C62*7, C74*8-53 (E1) L - W-B Ignition coil assembly (ignition confirmation signal) Idling with warm engine Pulse generation
(See waveform 11)
C62*7, C74*8-103 (PR) - C62*7, C74*8-135 (EPR) L - V Fuel pressure sensor signal Idling with warm engine 0.5 to 4.5 V
C62*7, C74*8-104 (THW) - C62*7, C74*8-105 (ETHW) L - BR Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
C62*7, C74*8-106 (PIM) - C62*7, C74*8-137 (EPIM) R - V No. 2 turbo pressure sensor signal Idling with warm engine 1.0 to 4.5 V
C62*7, C74*8-107 (THIM) - C62*7, C74*8-53 (E1) BR - W-B Intake air temperature sensor (No. 2 turbo pressure sensor) signal Idling with warm engine 0 to 5.0 V
C62*7, C74*8-108 (PTA) - C62*7, C74*8-139 (EPTA) B - V No. 1 turbo pressure sensor signal Idling with warm engine 1.0 to 4.5 V
C62*7, C74*8-110 (VCNE) - C62*7, C74*8-53 (E1) L - W-B Power source of crankshaft position sensor (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-111 (VCE1) - C62*7, C74*8-53 (E1) W - W-B Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-113 (VCV1) - C62*7, C74*8-53 (E1) L - W-B Power source of camshaft position sensor (for intake camshaft) (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-121 (VCTA) - C62*7, C74*8-120 (ETA) R - G Power source of throttle position sensor (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-119 (CLS)*10 - C62*7, C74*8-87 (E2CL)*10 G - W Clutch pedal stroke sensor assembly signal Ignition switch ON and clutch pedal fully released 0.2 to 1.5 V
Ignition switch ON and clutch pedal fully depressed 2.5 to 4.8 V
C62*7, C74*8-122 (VTA1) - C62*7, C74*8-120 (ETA) BE - G Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.1 V
Engine running, accelerator pedal fully depressed 3.2 to 4.8 V
C62*7, C74*8-124 (KNK1) - C62*7, C74*8-123 (EKNK) B - W Knock sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 18)
C62*7, C74*8-130 (VCPE) - C62*7, C74*8-53 (E1) B - W-B Power source of oil pressure sender gauge assembly (specific voltage) Engine stopped, ignition switch ON 4.75 to 5.25 V
C62*7, C74*8-131 (A1A+) - C62*7, C74*8-53 (E1) Y*6 - W-B
G*4, *5 - W-B
Air fuel ratio sensor (sensor 1) signal Engine stopped, ignition switch ON 3.0 to 3.6 V*9
C62*7, C74*8-132 (A1A-) - C62*7, C74*8-53 (E1) L*6 - W-B
R*4, *5 - W-B
Air fuel ratio sensor (sensor 1) signal Engine stopped, ignition switch ON 2.7 to 3.3 V*9
C62*7, C74*8-136 (VCPR) - C62*7, C74*8-53 (E1) G - W-B Power source of fuel pressure sensor (specific voltage) Engine stopped, ignition switch ON 4.5 to 5.5 V
C62*7, C74*8-138 (VCPM) - C62*7, C74*8-53 (E1) G - W-B Power source of No. 2 turbo pressure sensor (specific voltage) Engine stopped, ignition switch ON 4.75 to 5.25 V
C62*7, C74*8-140 (VPTA) - C62*7, C74*8-53 (E1) GR - W-B Power source of No. 1 turbo pressure sensor (specific voltage) Engine stopped, ignition switch ON 4.75 to 5.25 V
A38-14 (EC) - Body ground W-B - - Ground Always Below 1 Ω
C62*7, C74*8-18 (E04) - Body ground W-B - - Ground Always Below 1 Ω
C62*7, C74*8-47 (GE01) - Body ground BR - - Shielded earth (ground) circuit of throttle actuator Always Below 1 Ω
C62*7, C74*8-49 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
C62*7, C74*8-50 (E02) - Body ground W-B - - Ground Always Below 2 Ω
C62*7, C74*8-51 (E01) - Body ground W-B - - Ground Always Below 3 Ω
C62*7, C74*8-53 (E1) - Body ground W-B - - Ground Always Below 4 Ω
C62*7, C74*8-58 (E1D2) - Body ground Y - - Ground Always Below 5 Ω
C62*7, C74*8-59 (E1D1) - Body ground L - - Ground Always Below 6 Ω

*1: for CVT

*2: w/ Entry and Start System

*3: w/o Entry and Start System

*4: w/o Differential Pressure Sensor (for Rear Air Fuel Ratio Sensor Type)

*5: w/o Differential Pressure Sensor (for Rear Heated Oxygen Sensor Type)

*6: w/ Differential Pressure Sensor

*7: for TMMT made

*8: for TMC made

*9: The ECM terminal voltage is contact regardless of the voltage output from the sensor.

*10: for Manual Transaxle


WAVEFORM 1


A283576E01
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A283577E01
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 3


A304647E05
2.573,0.073 3.156,0.292 0.583,0.219 10 false 2 V/DIV. 2.563,1.948 3.323,2.177 0.76,0.229 10 false 2 ms./DIV. 2.802,1.635 3.385,1.854 0.583,0.219 10 false GND

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 2 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 4


A283573E11
2.677,0.125 3.354,0.385 0.677,0.26 10 false 2 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 false GND 1.156,1.99 2.219,2.167 1.063,0.177 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 5


A282867E05
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND 0.063,0.063 0.708,0.344 0.646,0.281 10 false 1 V/DIV. 1.344,1.854 2.208,2.083 0.865,0.229 10 false 20 ms./DIV.

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 6


A283575E01
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly (for Intake Camshaft) Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 7


A208000E20
2.854,0.99 3.313,1.302 0.458,0.313 10 GND 2.635,0.26 3.313,0.552 0.677,0.292 10 5 V/DIV. 0.521,0.656 0.99,0.948 0.469,0.292 10 M+ 1.396,1.802 2.281,2.021 0.885,0.219 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 1) Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 9


A283575E02
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.115 1.021,1.375 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Cam Timing Oil Control Solenoid Assembly (for Exhaust Camshaft) Operation Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 10


A299080E12
0.125,1.281 0.458,1.677 0.333,0.396 10 false CH1 (IGT) 0.146,1.802 0.573,2.219 0.427,0.417 10 false CH2 (IGF1) 3.021,2.167 3.385,2.354 0.365,0.188 10 false GND 3.021,1.542 3.427,1.771 0.406,0.229 10 false GND 0.146,0.51 1.375,0.708 1.229,0.198 10 false 2 V/DIV. 1.438,2.604 2.667,2.802 1.229,0.198 10 false 20 ms./DIV.

Ignition Coil Assembly Signal (IGT and IGF Signal)
ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 11


A245848E22
2.854,1 3.323,1.354 0.469,0.354 10 GND 2.625,0.313 3.323,0.594 0.698,0.281 10 5 V/DIV. 0.479,0.625 0.844,0.875 0.365,0.25 10 M- 1.417,1.802 2.573,2.052 1.156,0.25 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 12


A205412E04
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor (Sensor 2) Heater Operation Signal
ECM Terminal Name Between HA1B and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 13


A218020E05
2.677,0.208 3.344,0.51 0.667,0.302 10 10 V/DIV. 2.802,0.938 3.292,1.26 0.49,0.323 10 GND 1.26,1.771 2.25,2.021 0.99,0.25 10 20 ms./DIV.

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 14


A200774E03
2.969,1.177 3.396,1.438 0.427,0.26 10 GND 0.083,0.073 0.698,0.292 0.615,0.219 10 2 V/DIV. 1.229,1.875 2.25,2.104 1.021,0.229 10 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 15


A255508E20
0.052,0.031 0.656,0.188 0.604,0.156 10 5 V/DIV. 0.167,0.656 0.49,0.823 0.323,0.167 10 CH1 0.156,1.448 0.479,1.615 0.323,0.167 10 CH2 0.094,0.844 0.49,1.052 0.396,0.208 10 (VV1) 0.083,1.604 0.479,1.833 0.396,0.229 10 (EV1) 3.052,0.813 3.396,0.958 0.344,0.146 10 GND 3.052,1.573 3.396,1.719 0.344,0.146 10 GND 1.271,1.865 2.021,2.042 0.75,0.177 10 20 ms./DIV.

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 16


A283571E01
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:

Data List item "O2 Sensor Voltage B1S2" shows the ECM values from the heated oxygen sensor.



WAVEFORM 17


A283572E01
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed will differ slightly depending on the vehicle.