The side collision sensor RH circuit (bus 1) consists of the airbag sensor assembly and door side airbag sensor RH.
The door side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B166D | Lost Communication with Front Door Pressure Sensor RH | ·
The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1). ·
Door side airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Door side airbag sensor RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| B166E | Front Door Pressure Sensor RH Initialization Incomplete | ·
The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1). ·
The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1). ·
Door side airbag sensor RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Door side airbag sensor RH ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) | ○ | - | - |
| The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) | - | ○ | - | |
| The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 4 | Pattern 5 | Pattern 6 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) | ○ | - | - |
| Door side airbag sensor RH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the side collision sensor RH circuit (bus 1) | ○ | - | - |
| The airbag sensor assembly detects a short to ground in the side collision sensor RH circuit (bus 1) | - | ○ | - | |
| The airbag sensor assembly detects a short to B+ in the side collision sensor RH circuit (bus 1) | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 4 | Pattern 5 | Pattern 6 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects an open in the side collision sensor RH circuit (bus 1) | ○ | - | - |
| Door side airbag sensor RH malfunction | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | ○ | |
| Detection Time | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the door side airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
Disconnect the connectors from the airbag sensor assembly and door side airbag sensor RH.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I5-2 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| I5-1 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I5-2 (BDR+) - I5-1 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I5-2 (BDR+) - I5-1 (BDR-) | Always | 1 MΩ or higher |
| I5-2 (BDR+) - Body ground | Always | 1 MΩ or higher |
| I5-1 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connector to the airbag sensor assembly.
Interchange the door side airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B166D or B166E is output | A |
| DTC B167B or B167C is output | B |
| DTCs B166D, B166E, B167B and B167C are not output | C |
Codes other than DTC B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SIDE AIRBAG SENSOR (for Front Door)>REMOVAL
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Door Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
Disconnect the floor wire connector from the front door wire RH.
Check that the connectors (on the floor wire side and front door wire RH side) are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Door Side Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Service Wire |
| *a | Front view of wire harness connector
(to Front Door Wire RH) |
| *b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| IM1-40 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 25 (BBR+) and 26 (BBR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IM1-22 (BDR+) - IM1-40 (BDR-) | Always | 1 MΩ or higher |
| IM1-22 (BDR+) - Body ground | Always | 1 MΩ or higher |
| IM1-40 (BDR-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG